Injection pump oil hose

[FLYWHEEL]

Hi,
I am trying to find the part number for the oil line that feeds the IP, I've done several searches but cannot find the part number.
Also if anyone out there has replaced one can they point me in direction of someone who stocks these,
many thanks

 

[gringeltaube]

http://www.steelsoldiers.com/upload/M35/TM9-2910-226-34.pdf, Fig. B-2; Item #36: NSN 4720-879-1676; Oil hose assembly.

 

[FLYWHEEL]

Hi gringeltaube,
thanks for your reply but the one you have found is the same one that I keep finding, the one I am looking for runs from the side of the block to a connector on the bottom of the IP and then connects to the hose that you have listed

 

[gimpyrobb]

I had some new ones made up a while ago. Send me a reminder tomorrow and ill see if I have any left whenI get home.

 

[gringeltaube]

View attachment 687120Hi gringeltaube,
thanks for your reply but the one you have found is the same one that I keep finding, the one I am looking for runs from the side of the block to a connector on the bottom of the IP and then connects to the hose that you have listed

My bad; misunderstood.
I'll try to look into it, later on.
Although it seems that you already found a possible source... Thanks Gimpy!

 

[texas30cal]

I could use one too gimpy, if you happen to have 2 that is.

 

[gimpyrobb]

If I can't find any, ill have another batch run.

The way I see it, we're at 3. Anyone else?

 

[fowlhillbilly]

Over the counter. Make two hoses and leave the one in the block. I just went through this.

Sent from my iPhone using Tapatalk

 

[jbayer]

If I can't find any, ill have another batch run.

The way I see it, we're at 3. Anyone else?

I'm in for one please.

 

[Scar59]

If I can't find any, ill have another batch run.

The way I see it, we're at 3. Anyone else?

Count me in on 1 ea.. I'll need it eventually. Hope all is going good.
JC

 

[frank8003]

Is the lube oil line the small hose at the center of this picture?
This photo is for the fuel hose but this post is about the oil line, right?
I remember I bought some on SS but there is two and I could get to only one of them...

 

[FLYWHEEL]

If I can't find any, ill have another batch run.

The way I see it, we're at 3. Anyone else?

would you able to ship to the UK, if so put me down for 2

 

[gimpyrobb]

would you able to ship to the UK, if so put me down for 2

I can and will.

 

[gimpyrobb]

Is the lube oil line the small hose at the center of this picture?
This photo is for the fuel hose but this post is about the oil line, right?
I remember I bought some on SS but there is two and I could get to only one of them...
View attachment 687211

Yes, that is an oil line. The O.P. has that one, but the lines I have made are in sets. One is from the motor block to that Fitting and the other is the one in your pic.

 

[gimpyrobb]

Looks like I'll have 10 sets made up.

 

[texas30cal]

Sounds good

 

[Bill W]

If I can't find any, ill have another batch run.

The way I see it, we're at 3. Anyone else?

Me to, all ready PM'd you

 

[gimpyrobb]

Bill, please pm again. My inbox was full.

 

[gimpyrobb]

5here wasn’t enough material to have all 10 sets made. I will post a classified after I hear back from the OP. I will probably have the rest by next week.

 

[DavidWymore]

No hurry but I'd go in for one