• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

What did you do to your deuce this week?

Seth_O

Member
625
7
18
Location
Sac CA
My Sherman had a good week this week:

  1. re-bled the brakes and topped off the fluid
  2. my first oil change! $125 bucks later :-(. The oil was in great shape though, no sludge and no shavings or metal pieces. The WMO was good enough I felt ok pouring it into the fuel tank.
  3. fixed a stripped-out bolt hole on the compressor. The rear, top left bolt on the casing (where the fuel line bracket attaches) stripped out a little while ago and it's been causing the engine to pick up a light film of oil everytime I drive it. It's been nagging at me for a while, but I have been holding off on the fix since I needed to remove the oil filter cannisters and I knew I had an oil change coming. I drilled and tapped it, and inserted a heli-coil. The operation went smoothly and appears to have fixed the issue. Whew! Feels a lot better know - I hate it when I have those nagging fixes in the back of my mind that I haven't gotten to yet.......
  4. Installed a pyro. I used the most common location (pre-turbo, right where the exhaust turns down). I installed the Aubern digital 24v pyro. With the air filter cannister removed, the access and installation was a snap. I drilled almost all the way through, then fired up the engine and drilled the rest and tapped it 1/8" NPT. I ran the wiring and fired the truck up and watched it work great :jumpin:.
I still need to build a bracket to mount the gauge, once that's done I can get some baseline measurements and turn the fuel up. I have a suspicion that my fuel is low, and I have lots of overhead to get more power out of my engine. We'll see.....
 

Attachments

Last edited:

Recovry4x4

LLM/Member 785
Super Moderator
Steel Soldiers Supporter
34,012
1,808
113
Location
GA Mountains
Sounds nice. In regards to the question in the title, I started mine! Hasn't been touched since the FL Rally in Feb.
 

Heavysteven

New member
2,090
10
0
Location
Hickory Flat Ga
Drove yesterday for an hour. I blew out the vent line from the airpack and mc to the slobber tube. Turned up my regulator from 110 psi to 120 psi. Lubed the air horn. Checked return springs on brake, clutch, and parking brake. Wind out and wind in the winch cable.
 

Tinwoodsman

Well-known member
Steel Soldiers Supporter
3,923
76
48
Location
Comfort, Texas
Originally I planned to refurbish my drivers seat but spent the weekend fighting the door hinge screws. I am down to 4 of those suckers who are just unwilling to see it my way. I keep on soaking them and using my hand impact tool until the screw heads strip or break off. I should have posted in the "hardest bolt to remove" thead.
 

hdmax

New member
188
5
0
Location
new Lexington, Ohio
Whenever a thermocouple is installed before turbo, make sure you never allow the temperature to exceed about 1,000* as this placement is not the reccomended spot, and will read 300* +- lower than if it were installed in the manifold. (Which it the ideal place.)
 

dmetalmiki

Well-known member
5,523
2,028
113
Location
London England
Things to do

(See the adventure begins). My projects for this new addition. (m35). 1st IMEDIATE job, Fitting an enging oil prelube pressure pump!. 2nd. Fit a "wolo" air horn on the hartop. 3rd. Siren Kit. 4. Front towing glad hands.
5. 1100x20 tires. 6. Winch kit. 7. might (reposition) lift the steering wheel for more room. Should keep me occupied for a while. will post progress. 8. noticed someone re-covering thier drivers seat. also something that needs to be done. 9.just notice my pic..needs canopy lengthening both sides. oh! and 10. add stalk repeaters to the front side/flasher flights.
 

Attachments

To the tinwoodsman. If those hinge bolts are still stuck in the hinges here is my methodology to remove them. This usually works unless the rust is real bad.
After the bold head has broken off remove the nut on the other end and put a few washers on that end and replace the nut. Use lots of good grease on the washers and nut. Be sure at least one full thread protrudes out of the nut before you begin tightening the nut. Also, be very careful to stop when you get to the end of the threads or the bolt will break again. Keep adding more washers and drawing the bolt out till it falls out.
There are bolts in other machines that get stuck just like these hinge bolts do. Most of the time this method will do it. Just be patient/persistent.
I'm hoping it comes out clean for ya'.

e
 

gimpyrobb

dumpsterlandingfromorbit!
27,786
755
113
Location
Cincy Ohio
Whenever a thermocouple is installed before turbo, make sure you never allow the temperature to exceed about 1,000* as this placement is not the reccomended spot, and will read 300* +- lower than if it were installed in the manifold. (Which it the ideal place.)
Not sure I agree with this. Where else but the manifold is before the turbo?
 
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks