Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.
I put liquid teflon thread sealer on the block side and anti seize on the nut side. The studs are like butter. I can feel them start to stretch at 50lbs. The TM9-1804a in section 90 - "Tighten the cylinder-head bolds with a torque wrench from 65-75lbs...." It does say bolts not nuts. I see that...
I ordered some new head studs about 2 years ago and when I started assembling the other day I broke some of the studs at 70ft lbs. Since I couldn't remember who I order them from I reorder from 2 different vendors since one had the long studs in stock and the other the regular or short studs. I...
Thanks, I sent a message to them. It's not on their web site but that doesn't mean they don't have it.
I took the old one and put it in hot oil for about and hour. Just under boiling temp. Amazingly the thing is working but I think I still want to replace it. They must get gummy inside from...
I have a 24v stub nose starter for my M38. The starter works great but the overrun clutch is slipping. This part seems difficult to find and I don't want to replace the entire starter when only the clutch is bad. Below is a picture and the PN with descriptions. If anyone knows a supplier that...
I did check the x dimensions from the shock mounts and the shackle mounts. Both before and after had less than a 1/8" difference. The strange thing is the dimensions are off in way that would indicate the frame is off in opposite directions so even if I could tweak it I don't know what direction...
I had to figure out a way to bend my frame back from a twist it had. I found this method effective and thought it might help others out there with similar issues.
I drilled 1/2 holes into my floor and used 3/8" drop in anchors. I then screwed in 3/8 eye bolts. This was done on all four...
Just got the spacer in today. It looks like its the correct fit. Posting a few pictures of the pinion with the spacer and the old pinion for reference.
O.L. seems correct with the inner bearing pressed in place. I think this is a design improvement. The shims now have more surface area to land...
I think I have figured it out but I am still open to comments. I found this part...https://www.willysjeepparts.com/Ring_And_Pinion.htm
Part number 639968 pinion spacer.
I found this data on http://buyaircraftparts.com/part-number/639968. It sounds like the right part but it is usually called...
My Ring and pinion are badly worn so I got a new one the other day. Same PN 18396 and same manufacture - Salisbury.
My problem is the shoulder is different that the shims rest on and the over length is shorter for the outer bearing and yoke. I think there is a spacer or some kind of bushing...
I am in the process of rebuilding my L134. Got it back from the machinist and I'm getting ready to put it back together. I am debating if the Connecting Rod bolts, nuts and lock nuts should be replaced. I am thinking there is no need. These are low compression over built engines but I thought I...
After some research I think the Exhaust valve is from a later model F head. Mine if the L head. I assume this was the practice during the rebuild process to "upgrade" the L head non rotating valve with the F head valve and a rotating cap. Can someone confirm this and point me in the right...
your right.The valve on the left is the new valve and uses a different type of retainer. Anybody know where I can but a new rotating type exhaust valve?
That makes sense. I think I want to keep the rotating style. My caps appear to be in good condition.
Can I use the new exhaust valve with a different type of retainer. It looks like the new valve has the same retainer as the new and old intake. I am trying to figure out if the rotating valve...
I'm a confused on the types of valves used in the L134. I am in the process of rebuilding my M38 and have torn it down and had the block machined. Hardened valve seats are installed. I purchased new valves and the intake appear to be a direct replacement. However, the exhaust valves originally...
I have finally started my M38 Project.
I decided to post project to a blog page since it is easier to post high res images. I plan to post major events and pictures on this thread but for those who want to know more detail info you can visit. www.M38.us
I'm sure I will have a lot requests for...
A quick update...
I went to see Bill at EZ License about 3 months ago. He did a great job filling out all the paper work and his fees are very reasonable. Today 11/18 I received a letter from the IL SOS dated 11/5 that I need to get the State of SC to supply a surrendered title within 30 days...
Downloaded the application and will fill it in and send the $20 in before the end of the week.
I called Bill in Elgin and he seemed helpful on the phone. I plan on dropping off the BOS and VIN info this week. I will update this forum as to the progress. Thanks for the help.
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!