Search results

Will an M274A2 mule fit inside a 2010 Ford F250 with an 8-foot bed? The distance between the wheel wells is 49.9 inches. The specs on the Mule have the width at 50 inches, but I don't know if the distance between the outer side of the Mule wheels is 50-inches or some other part of the mule...

I would suspect that you have a bad coil. Loss of spark after the coil warms up is a classic coil failure. You mentioned that it wouldn't even fire with starting fluid and that is a dead giveaway. Try to find a new U.S. made coil. The Chinese ones are junk.

I like carbon dioxide or Halon because they don't make a mess.

No, the inlet tube wasn't completely closed, only about 50% closed off. It was obvious that the damage to the tube occurred years ago, likely when the engine was removed while the Army still had it. There was heavy grease and dirt all over the tube where the damage occurred, and no sign that...

I pulled the outlet tube from the compressor. Zero air coming out, so I pulled the head. Obviously, the valve is bad. I ordered a new head complete with both valves. The cylinder bore looked perfect, so I didn't pull the piston. I also noticed that the inlet tube was smashed almost closed...

Welcome from Hiawassee, Georgia!

Welcome to the forum. The first thing to do is download all of the TMs, all of which are located on this site. M35A2 trucks don't necessarily leak oil or grease. Poor previous maintenance is usually the culprit. You obviously need to replace both front boots and axle seals. I would...

I know the compressor is supposed to run all the time, but it was charging the tanks until I swapped the wiring harness with a new one. I guess it's possible there was a failure somewhere in the pneumatic system that coincided with my work. I don't hear any mechanical noise from the...

I'll try my M1030M1 USMC diesel motorcycle again.

I know you said that you checked the hydraulic fluid, but did you check both tanks? One is 11 gallons and the other is 21 gallons. One is for the front and the other is for the rear. You also said that the belt wasn't squealing, but it could be slipping without noise. Curling the loader...

I'm in the middle of replacing the front wiring harness on my FLU419 due to severe mouse damage. I have it installed, but some things don't work anymore. I'm slowly getting it sorted out with about 98% functionality. However, one of the things that has me puzzled is the air compressor. The...

Have you downloaded and read the TMs? How about the Student Handout? The Student Handout is particularly useful with the FLU419. I've attached a copy in case you don't have it.

I have an M116A2 with an MEP003A mounted on it and I believe the cover is identical with what you need. It is exactly as pictured in the diagram. I have attached a photo of mine installed. The dimensions are as follows. Length: 10 inches Width: 2-3/4 inches Height: 3 inches Screw Holes: 4...

I installed the new battery / accessory switch. Changing the switch was a royal pain, laying on my back with my head under the dash. Everything works and the engine starts fine now. The problem is that right before I installed the new switch, everything started working. I have no idea if...

That was the first thing I tried, but no joy. My NOS switch just came in today. Not looking forward to replacing it as there is virtually no room. I'm also replacing the starter relay. I know it doesn't have anything to do with my current problem, but it is extremely corroded. Part of the...

I've disconnected everything and cleaned the connections. I have 24VDC at both the starter relay and solenoid. There are two separate wires labeled 11 feeding the battery/accessory switch. The switch sends power to the windshield wipers and heater blower on one leg and the other goes to...

Those frequency gauges are very unreliable. You should get a Kill-A-Watt and plug it into the convenience outlet. I have the Kill-A-Watt EZ model. They work great and are very accurate.

Last year, back in October, My M35A3 refused to start when I tried to depart from the Southeastern Military Vehicle Rally. With the truck in neutral and the accessory switch on, engaging the start switch did nothing. The instruments came on, but the low air buzzer did not, even though the...

Is there a reason not to install the soft start directly on the generator and run all single phase output through it?

Where is the brake light diode mounted? Mine was simply hanging on the end of the wire on the front wiring harness and not mounted. I couldn't find it in the TMs. EDIT: Found it.