Search results

I see what you did there...

I know NDT already answered this part, and I'm going to second his reply. I just went through this on my A1. A lot of things had been altered, swapped, taken off completely on it. I'm not going back to 100% original by any means, but I want it to at least look closer than it did. Mine had a YF...

It runs again, still leaks too. Starting to think that the small chunk of missing block is the culprit. Of course, I can't tell without pulling the engine back out. This is after roughly 15 minutes of run time. I realize it's not easy to discern just how much is there since there's floor-dri...

New carb on, fuel fittings sealed and not drippy, radiator flushed and filled (it has a leak naturally), it starts and runs on it's own now with no hesitation. Good oil pressure, holds around 25 or so once it warmed up. Probably going to get a new exhaust setup. Again, the hack job by the PO...

Man, it's been a headache the last few days. Messing with the mechanical fuel pump, it works off the block just fine. Mount it, no pressure at all. Of course, initially I had it plumbed in reverse! In my defense, I'm so used to having the inlet facing the rear of the vehicle, that's how I set it...

Forgot I had smaller ones! Cleaning up the tool boxes today and ran across these, so ya know I had to install them. Little drill and tap action and they're ready to go.

You are correct, I was informed that they were either cadmium or zinc plated. Don't know why I didn't think of that to start with. Part of my job is plating....

What you do on a day when the big projects are basically on hold for whatever reason. Made a beauty plate to cover up the cluster of holes in the dash and cleaned up the seat frame chains. Interesting how one is a gold toned metal and the other is steel grey.

This is from a few days ago, I was pretty happy to hear it run for the first time in over five years. But, like the link reads, throttle shaft is toast. Gotta get that straightened out before I can move forward. So, today was a slow day. I took the cushions off the seat frames and cleaned...

Stuck my floor pans in today, pedals attached and leak checked the patch in the fuel tank. Had one small seep, took care of it, and now for the internal cleaning of it.

Absolutely correct, I have an early. Delivered May '53. I surprisingly still have the correct fenders, but somewhere along the line, my battery box cover was altered. Still has all the thumbscrews, but all eight tabs were cut off the sides and a stud was added to each end.

The grille unbolts from the radiator and the inner fender wells and can be swung face down. This allows the entire powertrain (radiator, engine, trans and transfer case) to be taken out as one unit. That's pretty much the reasoning, but yes, you could get to the fins that way too.

I bounced around a lot today. Clean here paint there, just didn't feel like it was a very accomplishing day. But, I got the grille painted, and mostly reassembled. I swept up the pile of paint and filler remnants, really didn't feel like laying in it if I didn't need to. I don't want to even...

I spent a good five years building commercial mufflers, I know a few tricks. What I ended up doing was after welding up the three inner sides (almost, but not quite to the outer corners) took a hammer and slowly beat the edge down to match the radius. I really didn't cut too far into it, so...

Today's project. Went rather well, with the exception of out at the seam, where some of the lead solder remained. Had to grind out and re-weld a few times to burn out the solder. Gonna try performing electrolysis on this tank, it needs a good cleaning out. Got some headlight pieces primed...

Just a few more gallons.

I did a thing today....and I totally understand now why it's easier to take out the entire power train at once! But, it's back in again, and I have this huge clearing in my shop now, odd how much space an engine on a stand takes up. Got this A1 tank today for the low cost of shipping it from...

Agreed 1000%! It sure wasn't a beauty when they finished it, so I'm not sure what they were going for.

Ok, all the big parts are done! There's still all the small nooks and crannies yet, (wheels and bumpers too lol) but it's time to move on to some very minor body work. I'm not spending a ton of time on it. Just filling some of the bigger holes is all, otherwise I'd be spending the next month...

Fair enough! Even though there's plenty of other faults I've deliberately left lmao!