Search results

Might try and take a little funnel and take the fuel line off at the PT and pour diesel down the hose until you hear fuel running in the tank, that has worked for me before. Also there is a plug on top of PT you can take that out and pour fuel in it to help prime system. hope this helps?

There was no spacer on the original flywheel housing, and we put the old housing on the new engine. I will change starters today and see if that fixes things, Thanks

So changing out the engine that came out of a M939 series truck into a M818 we put the starter that came with new engine, all worked fine with changing the front of engine. The starter was off the M939 series engine and it is dragging bad. Do I need to shim it back/out? It is fresh rebuilt so I...

Can you get someone to try to pull start you?

Which direction? As the clock turns or as time goes backwards? Thanks by the way.

So where to start? My nephew blew the engine in the M818, long story short, we got a new engine from Kansas (Glen) and it came with a Allison glued to it. I have both engines sitting on the M1061A1 trailer so I can put stuff that belongs off one to the other. We took the Allison off today so we...

I had a hydraulic hose break on the M936 and it drained all the oil out of the storage tank. Has anyone played with the idea of installing a ball/gate valve so if this ever happens again one could shut it off saving oil? Is the any maintenance that need to be done before I refill? Is it a good...

The last time I loaded a trailer solo, I wired a 2 x 12 board down on the dovetail on the goose neck so the jack would slide better/easier while using a come-a-long to pull. Hope this helps

Would you all mind helping design a trailer out of a 1973 white tractor truck. The truck is being scraped out but this is my idea. I will leave all axles rolling on 1100-20's on the frame front axle included, what I need is ideas how to make the front wheels follow the 5 ton's like a M989A1...

There was one thing that I am not sure went back right, inside the governor weights there was a needle with some shims and a small spring, they fell out when getting out of the bucket, the shims stayed on so we knew what side of the needle the shims stayed on. This is how we put it back...

The Ranch bought a M923 that had been sitting for who knows how long. Long story short the PT pump was gummed up (remind you of pine tar) the throttle shaft was so sticky that the spring on the throttle linkage was not strong enough to pull it back to Idle, so reaching down or pulling up with...

Very cool!!!

That is a good idea, I will give it a go, thanks

I have trouble getting a grease gun on the zerks on the short drive line that hooks to the engine (5 Ton), does anybody have a trick they would like to share? I have tried a needle with no luck, thanks in advance.

I learned this on SS, put your truck on level ground (if you can?) with a full tank of air in your M818 jack one front tire off the ground, get in the cab and put your truck in FIRST with ENGINE OFF, get out and turn your front tire that is jacked up forward (It should only go forward, if you...

I would drain the Transfer case and fill it with clean diesel, drive it for about 3-5 miles (with no load) and flush, repeat till clean diesel comes out. Fill it with 80w-90 and see if that helps? Remember not to let truck roll forwards when in reverse and vice-versa. Do you hear air when you...

No, sorry. He advertised the truck on SS and so maybe you might find a old photo of it?

No, got a guy that is looking at it.

I bought a M923 out of AZ that came with a Red Dot AC unit installed, I did not try it to see if it worked, no offence but it made it look like a sissy girl truck so I took it all off. The part that I really do not like is all the holes it has to have to plum everything in the cab, this truck...

It came apart when I was moving the Wrecker, I took it off after it failed. The Wrecker never gets on the highway, so can I just plug it for now?