Search results

Call Tabitha in the special plates division shes is the only one that can help you. Marty

I think is gonna be all good talked to lady today it's off site at a truck yard they have forklift so I am gonna run done there with my three axle trailer and pickup and go get it! Thanks everyone!

Anybody going to Jacksonville Fl. I got a M105 just need off base so I can come get in two weeks! thanks Marty

I put everything I built In my photo albums once you click on avatar! click on picture to the left and hit MORE. PROFO Marty

Kurt no,problem I also have a 3D printer if you need small plastic parts also, For circuit board I run Eagle software, not to say anything wrong but if you update your boards later you may want to enlarge your flowthroughs and fill with solder I have to make boards for saltwater environments and...

I design and prototype circuit boards I also have a rapid prototype circuit mill that mills them up 6 inches square max size if you finalize schematic I can convert it to Gerber Files and run you a few circuit boards then if everything is ok you can take the Gerbers and email directly to a board...

rides better than my 2015 dodge 3/4 diesel no hooping,shakes or anything, wanting to do on five ton camper!

The pump should be turning faster than the engine cause the pulley on engine is larger just divide engine pulley size by pump pulley size and that's the ratio then multiply that number times engine rpm and that is the rpm of pump! Bet at 1000 rpm you see about 2000 rpm at pump!

Also I think Boyce bought the set that they had built!

All the last stuff is gone he sold the complete sets he had orders for, I have all the springs and some small items. When the oilfield crunch came there wasn't enough work to do the sideline stuff. Milling one hub took about 10 hours of machine run time! If you can find a honest person who...

He was the machinist that made them for me I had told him if he wanted to make them and sell them that was fine because that would mean I would have access to spare parts without setup fees, he is not making them any more cause it was too time consuming and you needed a five axis machine to do...

Also whenever going to special plate division in Louisiana talk to Tabitha she's knows what to do!

I got a cat 3126 engine to be picked up at Lockborne and seeing if anybody is going there that can grab it and I can get it from them in about 2 weeks? Thanks Marty

Thanks for the reply I went to the site and looked at appointment dates and there was only one day and they only allows from Tuesday-Thursday normally seems kinda difficult to get in, so I went ahead contacted Steve at Fastrack and he dropped price a lil so I had it shipped with them. thanks...

I have a crate 6' x 5' x 3' @ 250 lbs that i need picked up and if possible have a freight company get to ship to Broussard, La. I tried fastrack but its way over what i think it should be. Any sugestions? Marty

I got a chevy 350 with 1 ton chevy manual trans in my 67 power wagon with no problem the chevy output shaft and dodge transfer case shaft mate same splines, i had found a two speed pto and it worked with original winch to. MArty

I remember seeing that part where you can turn on fan for engine brake, the fans turns on and off but in Louisiana at 95 degrees it climbs to around 190-195 quick less than 2 minutes on hwy which I am pretty sure that means the thermostat is closed till then, then it slowly just a few more...

I have a 2002 m1078A1 with a 1999 cat 3126, I am uncomfortable with the operating temperture, it goes up to 215 before the fan kicks on, I would like to lower if possible, I have checked with a separate temp gauge in the thermostat housing and confirmed its within a degree or so according to...

Batterychargers.*** got them they got 24volt 7 amp and not to expensive less 100 bucks! also checkout charging chargers.*** they got the 10 amp 24 volts I use to charge and maintain my generators they are about 75 bucks work great!

Text me when you get time to be there etc. will try to make it!