Search results

Thanks Simp. When it does make the noise it also slightly slows down the truck. Don't think it is a minor rubbing thing. It is LOUD!

Hey guys need some advice. I have had large amount of water in my airlines. The wet tank is spewing large amounts of water and I am draining it 4-8 times a day. I ordered the rebuilt kit for the air dryer. Air is pouring out of the bottom of it. I did push the valve back closed as best I can but...

Can you go bigger than the PH520 and it still fit?

Hey, just wanted to get opinions on possibly getting a dump bed hoist installed on my M925A2s. I have two trucks, they are used primarily to pull my tractor around for commercial mowing. Part of the contract requirement is removing trash and debris from the properties. I do have a dump...

A lot of people are saying to switch to Dextron III. Is Dex VI the synthetic equivalent and would it be better than Dex III? What about the new Trans/Syd that Allison now recommends? Both of mine have 10W in them. One has about 40,000 miles on it and the other has about 12,000. Should I...

MAdams, I was planning on buying the boost and EGT gauges from MTG. I know the trans is rated up to 300 HP and about 1,000 lbs of torque. My question is how close can I get to those marks and still retain the reliability of the engine and trans? Simp, How is the big cam doing? Also why did...

Thanks Simp! Love your Youtube channel BTW. Hey have you ever messed with the Bosch pump? I do want to turn up both trucks but no way in **** will I touch it. I read most of the turning up the 8.3 thread and NO WAY. Sounds simple but...... We were looking at the wheel humps. I think they...

I just purchased a 2008 Terex M322 equipment trailer. The trailer is nice but I need to get my overall height lower. I pull a large tractor and as it sits, the top of the cab is at 12'11". I would really like to get closer to 12'6". What tire/wheel combo would you recommend to lower the deck...

I just bought an M322. I have the same question. Any ideas?

That would be awesome! If I can drive the mowers on and off that is what I need. I currently load the mowers on and off the bed of the truck by driving them into a pallet I custom made then using my loader on my tractor to load it on and off the truck. It works ok but even if the property...

Sorry, but which is the best choice for an M925A2? The Curt 15400 or the Draw-tite 41947? How is the install/fit/finish?

I commonly pull my tractor and bush hog combo. Usually around 16-20K. Pulls it fine. Still does 60MPH on the highway. I do want to turn both trucks up a tad though. Is the 2.5 ton version of this trailer much smaller or more practical?

I did a site search and didn't find much info on these. I have two M925A2's and I am wondering if these would be a good fit for the truck. I was also wondering if these can be converted into a dump trailer set up. I would also want to put 2 zero turn mowers on this. Could ramp brackets be...

I have an M925A2. I regularly tow my tractor with it weekly out of state. Tractor, Bush Hog, grapples and a load of misc stuff in the bed I am around 40,000-45,000 lbs total. No issues at all. Tranny does not heat up outside of normal range nor does the engine. It is a bit of a dog under...

Thank you very much. I was hoping it was a tille longer. May just have to order another PJ Trailer.

Does anyone know the deck length of these trailers? I see them often on Govplanet.com and want to know if they are long enough for my application. Thanks!

I found the leak. Is the oil pressure sensor located under the fuel filter on the drivers side of the engine? If that is indeed the oil pressure sensor it is leaking from there, running down the side of the engine and pooling at the bottom. Any suggestions on a repair or do I just need to...

It seems to puke that puddle out all at once after driving then stopping. It will drip while the engine is running then basically after that amount it stops even though the engine is still running. And to make it even more weird, it only does it occasionally.......

I had to add 2 quarts of oil yesterday morning. Dip stick was down to the add mark. I seems like it is coming from the open hole.

I have an oil leak that has developed after I had the oil changed. Am I missing a plug? Any help is appreciated!