Search results

Its been a while, but do you still have/making them? I have the A0 version that does not have those featurs so the morros fold in a wind...

Do not have them yet.. just did a quick Google to verify the part numbers. My AC work will continue later in February. Part of my LMTV camper build project. The Yeti.

The RD part numbers are included on both schematic and harness details. Charge sensor is just a low pressure sensor PN: RD-5-9165-0. Its a two contact on/off low pressure typical AC switch. High Pressure switch is more specific as it is 3 wire sensor with reference 5V, ground and signal: PN...

Update! Attempted to connect with RedDot with no success. Turned to MME, where I bought the newer GEN II unit and pleaded with them to request the diagrams from RD.... success! Got the wiring and harness diagrams. Christal Clear! I see the light. I am including it here so to help all.

Yes, you are quite correct. I have A0 that did not have AC at all. I was prepaired for that until I discovered that I have two more wires that are not on this diagram: Black/White stipe and Orange. I am guesing it is for the new protector box for some sensors. I am concerned that that...

So do you have a diagram for this unit? I'd love to see it!

Thanks Keith Knight, I do have that diagram. My challenge is I have 6 pin rectangular connector, not 4.

Does any one know of a diagram for the RedDot GEN II evaporator unit? I am looking for an electrical diagram to figure out the connectors wiring designations. I found one but it shows two 4 pin connectors. I have one 4 pin and one 6 pin. (the 12 pin plug shown connects with the included...

Yas, I like the last idea. Keep isolating circuits and record the pressure drop for each. I will report later... Thanks.

Oh, and trailer park valve also eliminated. Not planning on ever tawing air brake trailer...

UPDATE: ... got busy but a the leak fixed... sort off. Line fix was remarkably easy. Thank you General! Replaced both check valves and new connecting line since the oem was too short. Before lost pressure in minutes due to the obvious line pinhole. Now, however, still loosing pressure but...

Guess I'm replacing that line. Uffff. Life with LMTV. I'll post an update when done. Thanks for all the good info.

Thanks. I just did that, removed the short line and figure out the fitting swap. NAPA. good advise. as to the pinhole, I think it is a break line or could be CTIS line. It is the same as the 1/2" pri-tank feed line. I need to free them out and trace to varify. It is pressure line and...

Also, on the reroute subject: on the wet tank the line to the e-gl is smaller then the once connecting wet tank with the pri-tank. I will need new fittings to make this work. Off hand, do you know what thread goes into the wet tank? I'd replace it with a straight fitting for better direction...

UPDATE: so this was NOT were it was leaking from! I was misslead by tagging on the line as it was causing the sound change. The leak is from farther forward on the bigger line (do not yet know what line it is) thru a pinhole. Do I need to replace the line, or can I cut it here and join...

I replaced the front e-gh earlier this year with this: It does not appear to be the same as the one on the pri-tank....?

General/Rommar, than you for great direction. The line switch makes total sense. Now I understand why they call it the wet tank too! was my next question. I'll get the check valves. To make sure: KN23080. Right?

Thanks Rommar. I can fix this leak, but sounds like I have more issues. Most likely bad check valves. Already replace one on the glad hand. How would you go about diagnosing it? Just replace all the check valves?

I got the schematic, but no clear to me where is that junction and that line.

I have 1998 M1078 A0 that Im working on to get ready for off-grid camper project.... discovered air leak from this junction (see photos). I wonder if any one can ID what this line is and where is it going to. It is draining my air while parked. This is a view from under, looking over the front...