Brutus Brent
New member
- 6
- 0
- 0
- Location
- Las Cruces, NM
Last edited:
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
1989 M923A2 MRAP Aluminum Wheels.
- Thread starter Brutus Brent
- Start date
BenRoberts
Certified insane
- 1,367
- 208
- 63
- Location
- southwest/ohio
That is an interesting look
Brutus Brent
New member
- 6
- 0
- 0
- Location
- Las Cruces, NM
Yes Sir, its different any way and a lot of work to get the wheels to work.
- 62
- 1
- 8
- Location
- Atlanta GA
So what did you have to do to them for this to work on a M923A2?
71DeuceAK
Well-known member
- 1,513
- 416
- 83
- Location
- Fairbanks, Alaska
Looks sharp! Does this mean the CTIS is totally gone now?
Brutus Brent
New member
- 6
- 0
- 0
- Location
- Las Cruces, NM
These are Hutchinson wheels and after a few emails I was able to get a copy of the drawings along with the specific information to cut the lug nut seats on the back side of the wheels. The seats are ball and not tapered. I got lucky and found the bit on ebay and borrowed a magnetic drill and started cutting away. Thanks for the likes!
Brutus Brent
New member
- 6
- 0
- 0
- Location
- Las Cruces, NM
Yes the CTIS is gone but I have the ones that came on the Hutchinson wheels. I chose not to use them is all.
Motiracer38
New member
- 34
- 2
- 0
- Location
- Santa Clarita, CA
That looks good. What was the weight difference per wheel? Did your track width change at all? Are they still double beadlock?
Special T
Member
- 495
- 21
- 18
- Location
- Wetside/ WA
So all you had to do was put the correct taper on the bolt holes and it lined up?
I haven't seen an aluminum m rap wheel up close. Do you have any closeup pics of the wheels with the ball seat? I'm guessing most of the work came from polishing up those wheels. That's a ton of work but they look **** good!
- 2,657
- 2,179
- 113
- Location
- Sunman Indiana
I thought most, if not all mrap variants where a bigger bolt circle? Guess thats what I get for thinking....
Tornadogt
Member
- 720
- 6
- 18
- Location
- Adkins, Texas
Pretty sure they are off of Early Caimans, which was on FMTV axles. So the pattern is the same but they are only tapered for the lug nuts on one side
74M35A2
Well-known member
- 4,145
- 330
- 83
- Location
- Livonia, MI
The aluminum wheel + magnetic drill part doesn't make sense to me, but it looks like you got it to work.
- 2,657
- 2,179
- 113
- Location
- Sunman Indiana
Anyone know if those wheels are still 10" wide? They look at little wider to me. I'm looking for a wheel around 11" to get me to the 34,000 legal max on my rear tandems. Indiana gives you 800 lb per inch of wheel.
M925A2 with dump hoist
sawdustnsteel
Member
- 31
- 0
- 6
- Location
- las vegas, Nevada
I thought the same thing then figured bolting a base in the span of plate steel to lock on after centering would be the way to do it. that way you don't get drift or chatter from the bit
sawdustnsteel
Member
- 31
- 0
- 6
- Location
- las vegas, Nevada
still got the Bit used?
I didn't know that. Here is my 12" wheel project.
Attachments
- 2,657
- 2,179
- 113
- Location
- Sunman Indiana
Did you ever get to try them out? I've been curious how the Sand tails would handle weight, due to the low air pressure. I have a strictly off road job in the future that I once considered them for, until I saw the max tire pressure...
M925A2 with dump hoist
M925A2 with dump hoist
No, not yet. And you're right about the tire pressure issue. 26# is not very high. I was going to use them on an M51A2 but that fell through.
- 2,657
- 2,179
- 113
- Location
- Sunman Indiana
Let me know if you ever go to sell the wheels, thats exactly what I'm looking for!
M925A2 with dump hoist
M925A2 with dump hoist