ddmcse
New member
- 4
- 0
- 1
- Location
- guilford ct
sept 3 2017 ---fellas on the side of the road limited internet connection , can anyone tell the exact size of these 2 screws holding down the throttle control seen here ?
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Broke down, throttle control assembly screws needed
- Thread starter ddmcse
- Start date
topo
Well-known member
- 912
- 260
- 63
- Location
- farmington NM
Coarse thread 1/4 x 1/2 and they have a copper washer.
ddmcse
New member
- 4
- 0
- 1
- Location
- guilford ct
Correct ! Cannot thank you enough. Solves problem #1
Problem #2 will not start.
Hear tank pump joy and
Fuel present at secondary bleed valve.
Batts tired .
Additional deuce ENROUTE 3hrs away.
Problem #2 will not start.
Hear tank pump joy and
Fuel present at secondary bleed valve.
Batts tired .
Additional deuce ENROUTE 3hrs away.
gimpyrobb
dumpsterlandingfromorbit!
- 27,786
- 755
- 113
- Location
- Cincy Ohio
Check the fuel shut off rod
gimpyrobb
dumpsterlandingfromorbit!
- 27,786
- 755
- 113
- Location
- Cincy Ohio
If you follow this link, it will have a group of 6 pictures at the bottom of the first post. Remove the part in the first pic, and see if the fuel shut off rod moves freely. If not, that is your problem.
https://www.steelsoldiers.com/showthread.php?143476-How-to-remove-the-Fuel-Shutoff-Rod-on-the-IP
https://www.steelsoldiers.com/showthread.php?143476-How-to-remove-the-Fuel-Shutoff-Rod-on-the-IP
ddmcse
New member
- 4
- 0
- 1
- Location
- guilford ct
Does move freely but thought it supposed to spring back into run/7 position.
Last edited:
jamesbtowle
New member
- 1
- 0
- 0
- Location
- Kingwood Texas
[FONT="]ok I'm IN....now where do I go to ask a question. My 998 sat on the sidelines during Harvey because I could not start it...ck'ed all the obvious things but found if I wiggled the gear shift and moved it back and forth long enough I seemed to hit a spot and it would start....but it was too unreliable to take into action....need some advice on fixing the problem?[/FONT]
ddmcse
New member
- 4
- 0
- 1
- Location
- guilford ct
Would this make things even worse
How bad would it be if I miss aligned the throttle control assembly to the shaft it's inside this cover my guess is that I may have not lined them up correctly remember I'm am on the side of the road with cars whizzing by it's a little unsettling.
So my guess is the first time I reattach this cover I did not line the shaft up and then tried to turn it over .
luckily I have another Deuce show up to help Tomy from one spot to another and we have a spare pump to look at and learn what I am doing wrong it does seem that the fuel shut off and the throttle assembly are linked together somehow in the pump so I'm not sure if I've made things worse by missing the connection on the throttle assembly shaft.
Currently I am 3 hours away from the truck which adds to my dilemma and I will head back there tomorrow morning so I am trying to figure out when to throw in the towel and have it shipped somewhere so I don't have to keep traveling 6 hours a day to work on it on the side of a road.
When I took the fuel shutoff valve cover open it did appear that the shut-off was in the closed position which means it would never start so I am trying to figure out how it got that way and what to do about it but I'm just wondering if all my trouble obviously all my trouble started when the two screws fell out but have they made it worse or impossible to repair on the road thanks for all the help and comments I truly appreciate it
How bad would it be if I miss aligned the throttle control assembly to the shaft it's inside this cover my guess is that I may have not lined them up correctly remember I'm am on the side of the road with cars whizzing by it's a little unsettling.
So my guess is the first time I reattach this cover I did not line the shaft up and then tried to turn it over .
luckily I have another Deuce show up to help Tomy from one spot to another and we have a spare pump to look at and learn what I am doing wrong it does seem that the fuel shut off and the throttle assembly are linked together somehow in the pump so I'm not sure if I've made things worse by missing the connection on the throttle assembly shaft.
Currently I am 3 hours away from the truck which adds to my dilemma and I will head back there tomorrow morning so I am trying to figure out when to throw in the towel and have it shipped somewhere so I don't have to keep traveling 6 hours a day to work on it on the side of a road.
When I took the fuel shutoff valve cover open it did appear that the shut-off was in the closed position which means it would never start so I am trying to figure out how it got that way and what to do about it but I'm just wondering if all my trouble obviously all my trouble started when the two screws fell out but have they made it worse or impossible to repair on the road thanks for all the help and comments I truly appreciate it
