paramilusmc
Member
- 177
- 8
- 18
- Location
- Charlottesville, VA
So you had to give a buddy a jump from your CUCV, how and where do you hook up the cables?
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Getting jumped from a CUCV
- Thread starter paramilusmc
- Start date
- 14,635
- 4,793
- 113
- Location
- Buchanan, GA
To the front battery since it'd be easier to clamp on. Both batteries and alternators are 12v. You could jump even from the rear, so long as you're careful that the ground cable doesn't touch the body or the vehicles bodies touch each other. Front is a little safer.
ralbelt
Active member
- 1,056
- 9
- 38
- Location
- West Warwick, R.I.
Ditto, I have jumped several vehicles, used front battery only.
wired1000
New member
- 214
- 0
- 0
- Location
- Chicago, IL
While we're on the topic, jumping a CUCV would involve... two (12V) vehicles, one on each battery? A vehicle and a jumper pack, one on each battery? I suppose a 24V vehicle could be used jumped from front batt and the rear batt? Or use the NATO slave plug?
jaymcb
Active member
- 521
- 55
- 28
- Location
- Behind Enemy Lines, Massachusetts
2 12 volt vehicles would do it, as would a vehicle and a jump pack
- 14,635
- 4,793
- 113
- Location
- Buchanan, GA
A single vehicle could do it. Just charge each battery for a few minutes (10-15mins).
DriverSideImpact1008
Member
- 479
- 0
- 16
- Location
- Madison, WI
Yeah, what patracy said. I jumped my 1008 a few times with my Grand Marquis.
You should definitely carry two sets of jumpers. Your best bet for getting jumped is to find a guy with a 3/4 or 1 ton diesel truck (F-350, Dodge 2500, etc) as they have dual batteries.
You should definitely carry two sets of jumpers. Your best bet for getting jumped is to find a guy with a 3/4 or 1 ton diesel truck (F-350, Dodge 2500, etc) as they have dual batteries.
- 14,635
- 4,793
- 113
- Location
- Buchanan, GA
Just because a truck has two batteries does NOT mean it can jump you. You'll find out quick as to why not...
- 34,012
- 1,808
- 113
- Location
- GA Mountains
To the original poster, need to clarify what kind of vehicle are you jumping. If it's another CUCV, the directions posted may cause sparks.
91W350
Well-known member
- 4,414
- 57
- 48
- Location
- Salina, Kansas
Jumping a deuce or five ton? Slave cables are the easiest and best, without that luxury, you can use heavy jumper cables.
- 12,195
- 319
- 0
- Location
- gainesville, ga.
"Getting jumped from a CUCV" , when I read this, I first thought it ment gang banger thugs were now using cucvs as there victem stalking and get away vehicle
Last edited:
lindyp38
New member
- 788
- 0
- 0
- Location
- ulster county ny
yes...metoo..lol.....
K9Vic
Active member
- 1,261
- 7
- 38
- Location
- Fort Worth, TX
I do not know if the OP question was to jump start a normal vehicle with a CUCV, or jumping a CUCV with a normal vehicle. I think he was asking to jump a car with a CUCV.
I have both a 24v & 12v jumper system on my M1009 and can jump a 24v military vehicle with the OEM slave cable. I can also jump a 12v vehicle with a standard jump cable system as seen on tow trucks. I have jump started both vehicles many times, mostly 12v vehicles. As long as you are on the 12v side it is perfectly safe.
I have both a 24v & 12v jumper system on my M1009 and can jump a 24v military vehicle with the OEM slave cable. I can also jump a 12v vehicle with a standard jump cable system as seen on tow trucks. I have jump started both vehicles many times, mostly 12v vehicles. As long as you are on the 12v side it is perfectly safe.
paramilusmc
Member
- 177
- 8
- 18
- Location
- Charlottesville, VA
I was talking about jumping a regular vehicle with a CUCV.
So what I have gathered is use the front battery only.
Now I swear I read here before that when jumping a CUCV with a regular vehicle you place the negative on the father battery and the positive on the closer battery. Was I just smoking crack or is there a different procedure?
Now if you couldn't slave cable two CUCVs together (do to maybe lack of correct cables) then what could you do with regular cables?
Why not just make this an official CUCV jumping thread?
So what I have gathered is use the front battery only.
Now I swear I read here before that when jumping a CUCV with a regular vehicle you place the negative on the father battery and the positive on the closer battery. Was I just smoking crack or is there a different procedure?
Now if you couldn't slave cable two CUCVs together (do to maybe lack of correct cables) then what could you do with regular cables?
Why not just make this an official CUCV jumping thread?
Pawnshop
Active member
- 1,798
- 23
- 38
- Location
- Austin/Cedar Park Texas
I have used the slave port to jump many a Deuce and five ton, but my standard answer when asked to jump a 12v vehicle is "NO, my truck is 24v and will destroy your car's computer". If I knew (and liked) the 12v vehicle's owner and knew WHY it would not start I would likely disconnect my front battery and jump from that, or just let them use my battery to go get a new one for themselves. I have seen too many melted batteries and fried electrical systems to expose my daily driver to those dangers.
DriverSideImpact1008
Member
- 479
- 0
- 16
- Location
- Madison, WI
I wasn't really thinking clearly...
and I forgot that the two CUCV batteries are linked. Sparks would fly...I didn't really specify... If you isolate both batteries from each other in the CUCV and connect each battery in the other civi truck to each in the CUCV, and let them sit and charge, they seemed to charge up a little faster/more equally... that is assuming you have tools to remove the cables. I did that a few years ago with my roommate's powerstroke F250 on the old M1008. It worked enough to start it up.
But that's kind of a stupid, time consuming way to go...
emr
New member
- 3,209
- 25
- 0
- Location
- landing , new jersey
there are alot of threads on this i really would say read a ton before doing anything one may not be sure of,