-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Pulled the trigger on a M820
- Thread starter 802dot1q
- Start date
Makincold
Member
- 317
- 0
- 16
- Location
- Mansfield, GA
Was this the one out of Warner Robbins GA? Good looking truck!
Sirblissfull
New member
- 470
- 7
- 0
- Location
- New Mexico
Congrats I love my M820 and M820A2.
exbrown
Member
- 548
- 13
- 18
- Location
- West Union, SC
Congratulations on such a nice truck.
muddog
Member
- 343
- 0
- 16
- Location
- Spartanburg SC.
Sweet looking truck, hope you get her home soon so you can enjoy her.
khandoh
New member
- 30
- 0
- 0
- Location
- Warner Robin, GA
I was wanting that one, but decided against it at the last second. I wish the EUC for a first timer could be a little more traveler friendly... Good luck with her!
OTOH, if you decide you don't want her...
OTOH, if you decide you don't want her...
aaron379
New member
- 299
- 1
- 0
- Location
- junction city ky
whats the inside of the van look like? ive always wondered but never been in the back of one...... post some pics when u get a chance
R Racing
Active member
- 2,767
- 16
- 38
- Location
- St. Leonard, MD
Very nice truck !! You will love the 5 tons 
would love to have a m820A2 !!!
would love to have a m820A2 !!!scottjhl
New member
- 136
- 1
- 0
- Location
- Loxahatchee, FL
Drools... I love the expandable! SOO many possibilities...RV modification to it?
Sirblissfull
New member
- 470
- 7
- 0
- Location
- New Mexico
Aaron379
Here are some pics I have more of my A2 in my album.
Here are some pics I have more of my A2 in my album.
bbf
Member
- 461
- 0
- 16
- Location
- port st lucie fl
nice truck
R Racing
Active member
- 2,767
- 16
- 38
- Location
- St. Leonard, MD
I love the power lift gate !!! boy could that come in handy !!!
I never knew about those. That is VERY cool!Aaron379
Here are some pics I have more of my A2 in my album.
Sirblissfull
New member
- 470
- 7
- 0
- Location
- New Mexico
Most of the A2 versions I have seen come out of GL no longer have the platform attached if they have the hydraulics attached at all. Those lift gates can run off of electrical or a rear facing PTO.
I have a set of hydraulics for my 820 to turn it into an 820A2 just have not been able to get it installed and a platform built for it.
Just about nothing has gone right this last year.
I have a set of hydraulics for my 820 to turn it into an 820A2 just have not been able to get it installed and a platform built for it.
Just about nothing has gone right this last year.
R Racing
Active member
- 2,767
- 16
- 38
- Location
- St. Leonard, MD
Your A2 is a beauty !!!
91W350
Well-known member
- 4,414
- 57
- 48
- Location
- Salina, Kansas
SirBlissfull, Have you run across a scale yet? The dash data plate says 27,000 or something along that line and the box data plate says 19,000 or something close. Those trucks actually weigh 46,000 pounds? No wonder their fuel burning reputation is alive and well! Glen
- 3,220
- 390
- 83
- Location
- Tonopah, AZ
NIce Truck!!! Also the box looks to be in great shape also!!
Sirblissfull
New member
- 470
- 7
- 0
- Location
- New Mexico
The book on mine with lift gate says 29495 with singles I estimate the weight to be a bit higher but I would not say more then 32500.
I can swing by a scale next time I am driving without a bunch of crap in it and check for sure.
It is currently in use as a storage shed/moving van.
I know the van body weighs 6k or so.
The box WAS in great shape. When I bought it from GoldnEagle with all the humidity in that 30 year old plywood it was fine. As soon as it hit New Mexico that same plywood started disintegrating. The same happened to a few rust spots, there is some patch work needed. The wood and insulation need to be replaced as well. I am going to go with a much higher value insulation then the old pink fiberglass and debating using a vinyl board for the interior lining.
I can swing by a scale next time I am driving without a bunch of crap in it and check for sure.
It is currently in use as a storage shed/moving van.
I know the van body weighs 6k or so.
The box WAS in great shape. When I bought it from GoldnEagle with all the humidity in that 30 year old plywood it was fine. As soon as it hit New Mexico that same plywood started disintegrating. The same happened to a few rust spots, there is some patch work needed. The wood and insulation need to be replaced as well. I am going to go with a much higher value insulation then the old pink fiberglass and debating using a vinyl board for the interior lining.
Last edited: