mattgunguy
New member
- 290
- 2
- 0
- Location
- Springfield, Mo
Don't feel bad. I put mine on backwards. Took me a week to realize it.
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
What did you do to your deuce this week?
- Thread starter Seth_O
- Start date
Streetgliderx
New member
- 147
- 0
- 0
- Location
- Tuscumbia, AL.
Fixed it!!
Rmtaunton
Well-known member
- 1,510
- 31
- 48
- Location
- Smyrna, ga
That would be such an appropriate name for a Deuce!
wilfreeman
Active member
- 1,082
- 7
- 38
- Location
- Richburg, SC
+1 on that!
Rmtaunton
Well-known member
- 1,510
- 31
- 48
- Location
- Smyrna, ga
Mounted the FMTV wheels on front , thanks to Peashooter and G.
brianp454
Member
- 572
- 11
- 18
- Location
- Portland, OR
Captaincarrier
Active member
- 231
- 241
- 43
- Location
- St Pete, FL
Rmtaunton
Well-known member
- 1,510
- 31
- 48
- Location
- Smyrna, ga
I will get some this weekend , and going to do a DB test on the aero turbine muffler before and after
Towersafety
New member
- 20
- 0
- 0
- Location
- Ludlow Falls, Oh
The back is fine. At the top rear of the door windows it is about an inch to long. It fits all the little twist snap things but between the last (back) one and the vertical part it is an inch to long.
Towersafety
New member
- 20
- 0
- 0
- Location
- Ludlow Falls, Oh
I put in the new turnsignal blinker. Now none of the lights work. Time to trace wires. Oh Joy
TsgtB
New member
- 478
- 3
- 0
- Location
- Granbury, Tx
so its a little tight to get up in there....??? looking forward to it...
any advise you could pass on to make it easier.?
215Dave
Member
- 288
- 0
- 16
- Location
- Northeast Phila, PA
Clocked 250 miles and gave her a workout at Rauschenberg Creek. Loved it!
- 2,112
- 555
- 113
- Location
- Davis County, UT
Picked up the troop seat hardware from being powder coated at a local place! Still working on sanding the wood so it can be re-painted.
Also received my new custom license plates in the mail! Named the truck after an "old-timer" Autobot from the Transformers, Kup (later named Sergeant Kup). Hahah.
Mounted the plate below the passenger headlight. While drilling out the holes for the license plate mount, I thought to remove one of the arctic front cover lash points to get a more vertical drilling angle. I forgot that everything on the truck is thoroughly seized in place. Twisted the head right off the screw. Now I get to drill it out and put something else in its place. *sigh*
Also received my new custom license plates in the mail! Named the truck after an "old-timer" Autobot from the Transformers, Kup (later named Sergeant Kup). Hahah.
Mounted the plate below the passenger headlight. While drilling out the holes for the license plate mount, I thought to remove one of the arctic front cover lash points to get a more vertical drilling angle. I forgot that everything on the truck is thoroughly seized in place. Twisted the head right off the screw. Now I get to drill it out and put something else in its place. *sigh*
Is the A3 speedo a drop-in replacement for the A2? I'd love to have a trip-meter for my truck!
jbayer
Member
- 675
- 7
- 18
- Location
- St. Aug., FL/ McGrady, NC
Yes.
That's exactly why I added it. (For the trip meter)
That's exactly why I added it. (For the trip meter)
Last edited:
Where did you get it, if you don't mind my asking? I started poking around this evening, but none of my usual suspects has it.......
Pretty straight forward. Window stays up. Even with all the screws removed, it won't just fall out. There's a lip that the latch has to squeeze by. You'll have to reach up and wrestle it out, then the replacement back in. Put the latch end in first and start one or both screws on the jamb side of the door, then put the triangular end in. Shouldn't take more than twenty minutes start to finish, unless some screws are stripped.
jbayer
Member
- 675
- 7
- 18
- Location
- St. Aug., FL/ McGrady, NC
Found a complete panel on a VERY POPULAR auction site.