Jeeagle
Member
- 87
- 0
- 6
- Location
- Chattanooga, TN
The big two wire Jumper cable for the slave receptacles? Or the actual Socket deal?
We may have OE pumps but they would all need a rebuild if could be found.
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
What have you done to your JEEP today
- Thread starter zout
- Start date
We may have OE pumps but they would all need a rebuild if could be found.
- 6,555
- 13,939
- 113
- Location
- Hawthorne, NV.
Picked up an oil filter and mount.
Bravo2Uniform
Member
- 253
- 21
- 18
- Location
- McMinnville, TN
Bravo2Uniform
Member
- 253
- 21
- 18
- Location
- McMinnville, TN
Wearing new shoes...
Disk brakes installed...well, on the Willys anyway. Plumbing to commence soon.
Disk brakes installed...well, on the Willys anyway. Plumbing to commence soon.
Jeeagle
Member
- 87
- 0
- 6
- Location
- Chattanooga, TN
I looked in the Boneyard found none then asked Matt, Apparently few years ago when I was messing with a M38a1 myself for a museum I stole the last one. However I know I've found them online before with the appropriate wiring and pin in them between $30-$70. With the M38a1 I do know you will want the one with really long leads on the receptacle.
Bravo2Uniform
Member
- 253
- 21
- 18
- Location
- McMinnville, TN
I'll find one somewhere. The hunt is half the fun. I appreciate your help, though.
- 6,555
- 13,939
- 113
- Location
- Hawthorne, NV.
Purchased carburetor parts online for my M38A1.
Bravo2Uniform
Member
- 253
- 21
- 18
- Location
- McMinnville, TN
Grinding Caliper Travel
Finally got the nerve to grind the caliper gap on my new knuckles for the disk brake installation. Grind, fit, grind, fit, ad infinitum - these are the next to last fitting. When done and filed to reduce the roughness it looks fairly decent.
PRO TIP: Fill knuckle reservoir BEFORE attaching caliper permanently!!!
Finally got the nerve to grind the caliper gap on my new knuckles for the disk brake installation. Grind, fit, grind, fit, ad infinitum - these are the next to last fitting. When done and filed to reduce the roughness it looks fairly decent.
PRO TIP: Fill knuckle reservoir BEFORE attaching caliper permanently!!!
Last edited:
Bravo2Uniform
Member
- 253
- 21
- 18
- Location
- McMinnville, TN
Install a dual reservoir master cylinder, it'll be easy they said...
"Ourkit was designed to be an easy..." Sure for a person with an advanced degree in Hyperbolic Topology.
And the piece de resistance...the final paragraph of the installation instructions, "With all that done you should be able to install lines and finish setup." Well, kiss my grits, Mel, how 'bout some directions just in case?
"Ourkit was designed to be an easy..." Sure for a person with an advanced degree in Hyperbolic Topology.
And the piece de resistance...the final paragraph of the installation instructions, "With all that done you should be able to install lines and finish setup." Well, kiss my grits, Mel, how 'bout some directions just in case?
- 623
- 53
- 28
- Location
- Attleboro, MA
Still trying to work the bugs out, seems we have a carb issue now! We rebuild it and still having issues. In between the fuel pump died! I "think" we are getting close!
Another Ahab
Well-known member
- 17,999
- 4,556
- 113
- Location
- Alexandria, VA
It's astounding how useless some installation directions can be. I never understood that.
- 623
- 53
- 28
- Location
- Attleboro, MA
OK, she is running! Made a 30 mile run with no issues! Fingers crossed! Also added the BO drive, markers, Slave Recpt, and the 1st aide kit.
For some reason pictures are not uploading? Maybe later!
For some reason pictures are not uploading? Maybe later!
Bravo2Uniform
Member
- 253
- 21
- 18
- Location
- McMinnville, TN
congratulations!!!!!
- 623
- 53
- 28
- Location
- Attleboro, MA
OK, now I had a double post! Weird bugs on my end this weekend!
Attachments
Last edited:
- 623
- 53
- 28
- Location
- Attleboro, MA
OK, now I can load a photo! She ran fine, no issues, only 6 months and a ton of money! 
View attachment 621808View attachment 621807
View attachment 621808View attachment 621807
Last edited:
Another Ahab
Well-known member
- 17,999
- 4,556
- 113
- Location
- Alexandria, VA
Your jeep looks great:
- I never noticed headlight guards on any of them before; nice item.
- I never noticed headlight guards on any of them before; nice item.
- 6,555
- 13,939
- 113
- Location
- Hawthorne, NV.
Just purchased a decent Carter YS950 carburetor, along with the correct Fram oil filter and mount for my M38A1.
- 623
- 53
- 28
- Location
- Attleboro, MA
Putting on the new NDCC's! 
Another Ahab
Well-known member
- 17,999
- 4,556
- 113
- Location
- Alexandria, VA
I'm taking a guess (S.W.A.G.) here:
- Non-Directional Circular Conductors?
You know what I mean, right; "tires"!?
- 623
- 53
- 28
- Location
- Attleboro, MA
Wow!, You got it first try, you're awesome!