- 2,111
- 63
- 48
- Location
- Maine USA
Care package from TX today, all parts in stock, speedy shipping and no overcharges, can't ask for any better service. Mark, thanks for bailing me out again. Now back to the garage.
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Operation "URGENT RESTORATION"
- Thread starter m38inmaine
- Start date
- 5,637
- 381
- 83
- Location
- Spring Branch, TX
Glad to help out. It'd be nice to be a little closer and I could just finish cleaning the shop out. Until then, one box at a time.
combat32
Well-known member
- 1,639
- 106
- 63
- Location
- Booneville AR.
When you gonna crank it up?
Don't let Mark infect you with LMTV talk
Don't let Mark infect you with LMTV talk
Last edited:
- 5,637
- 381
- 83
- Location
- Spring Branch, TX
Careful or I'll trade your generator for a tailgate.Don't let Mark infect you with LMTV talk
- 2,111
- 63
- 48
- Location
- Maine USA
My goal is to have it cranking by the weekend, I have to jerry rig a fuel supply as my tanks are off. I'm going to crank it off the slave cable for power. I would love to have a FMTV but for now I'll have to settle on the old goat.
- 2,111
- 63
- 48
- Location
- Maine USA
Throttle linkage-check, exhaust manifold blasted w/high heat paint-check, 13qt engine oil-check, getting closer..
Attachments
- 2,111
- 63
- 48
- Location
- Maine USA
Parts from Saturn Surplus today, easy to figure out what I'm working on next.
Attachments
combat32
Well-known member
- 1,639
- 106
- 63
- Location
- Booneville AR.
Snow cone maker?
You are gettin too far ahead, my work is gettin in the way of my work, I mean fun.
You are gettin too far ahead, my work is gettin in the way of my work, I mean fun.
- 5,637
- 381
- 83
- Location
- Spring Branch, TX
In Ahnald voice "This is an espresso machine. Is it a hot water heater?"
Last edited:
- 2,111
- 63
- 48
- Location
- Maine USA
Master cylinder installed, blew out the lines from the master cylinder end, not much air at the carrier so I detached the quick release and tried from there, still not much so I reversed and blew in the axle fitting and that started clearing the lines so back and forth a few times and now a good strong stream of air. Luckily it had only seen dot 5 and it was coming out clean. May bleed them tomorrow or Monday. Engine stop cable installed and throttle linkage finished and adjusted. Repaired the under front fender wiring harnesses so those are done. Last wire to repair is the fuel tank sending unit wire. Air duct installed and LH panel in place. My plan is to fire the engine tomorrow, if it lights I will fill the cooling system and run it and see if I can move it under it's own power.
Attachments
Jericho
Well-known member
- 1,180
- 69
- 48
- Location
- Landaff NH
good luck with your first start!
prodro1
Member
- 102
- 5
- 18
- Location
- Keithville, LA.
Looks awesome, good luck on the start.
wsucougarx
Well-known member
- 6,951
- 67
- 48
- Location
- Washington State
Really looking forward to the first start. You got to get it on video!
Sent from my XT1254 using Tapatalk
Sent from my XT1254 using Tapatalk
Another Ahab
Well-known member
- 17,993
- 4,541
- 113
- Location
- Alexandria, VA
It's sort of like this.
"The Flight of the Phoenix", a classic flick; do you know it?
Here's the clip. Good luck:
https://youtu.be/IACjOvyx5hs
Last edited:
- 2,111
- 63
- 48
- Location
- Maine USA
Video first, took a while to download with my primitive off grid connection, report to follow.
https://www.youtube.com/watch?v=g9gxfP5KkMw&feature=youtu.be
https://www.youtube.com/watch?v=g9gxfP5KkMw&feature=youtu.be
wsucougarx
Well-known member
- 6,951
- 67
- 48
- Location
- Washington State
Outstanding!!!! She lives!!!
Sent from my XT1254 using Tapatalk
Sent from my XT1254 using Tapatalk
- 5,637
- 381
- 83
- Location
- Spring Branch, TX
Nothing like the culmination of a long journey.
Another Ahab
Well-known member
- 17,993
- 4,541
- 113
- Location
- Alexandria, VA
You done it. You done it!
FANTASTIC!!!!
Do you have the rear canvas with the red cross since it is technically an ambulance like in these National Archive images below?
https://catalog.archives.gov/id/6375986
https://catalog.archives.gov/id/6374673
Do you have the rear canvas with the red cross since it is technically an ambulance like in these National Archive images below?
https://catalog.archives.gov/id/6375986
https://catalog.archives.gov/id/6374673
- 2,111
- 63
- 48
- Location
- Maine USA
Ok so she runs and it was quite exciting and as Mark said they fire pretty quick, so now the AAR. So my fuel supply was a jerry can with a return line and an outboard motor fuel hose for the supply. I chose it as it has a priming bulb which made it easy to fill the filters and prime the system. As the bulb got tight and she was primed I noticed a bad leak from the cold start filter, so I shoved a rag under it and started the engine. I used the slave cable for power as my tanks are off and no place to easily set the batteries. Also saw a smaller leak where the return line leaves the head, this is the same line that supplies the cold start. As you can see at the bottom of the filter it either chaffed or corroded a hole in the bottom corner. There is a TB describing eliminating the filter to allow for longer starters to be installed so I am going a step further and eliminating the cold start as it looks pretty trashed anyway. As easy as these start I doubt it would ever get used and I don't plan on traveling to the arctic any time soon. I pulled the mess off and all I will need to delete it is a 1/4" cap and a cap for 3/16 flare fitting.
So I did not put any water in yet as I thought if something was wrong with the engine I would not have the mess of draining the system, I would only run it for a minute. So after she runs for about a minute my son pulls the engine stop and nothing, now I panic she's running dry and it won't shut off. So I pull the fuel line and of course there is a lot of fuel still in the system, rag over the air intake next, nope still won't shut off so messing with the throttle and lack of fuel it shut off after 30 seconds or so. I had the governor cover off to remove the rod to get the head off/on and I did not position the shut off shaft correctly, it is now! I am happy that it seems I got the fuel rack adjusted correctly as well as the valves and injector timing. After I get the fuel leaks fixed I will fill the cooling system and let it get up to temperature. Then on to bleeding the brakes, the next thing to fight to the very end.
So I did not put any water in yet as I thought if something was wrong with the engine I would not have the mess of draining the system, I would only run it for a minute. So after she runs for about a minute my son pulls the engine stop and nothing, now I panic she's running dry and it won't shut off. So I pull the fuel line and of course there is a lot of fuel still in the system, rag over the air intake next, nope still won't shut off so messing with the throttle and lack of fuel it shut off after 30 seconds or so. I had the governor cover off to remove the rod to get the head off/on and I did not position the shut off shaft correctly, it is now! I am happy that it seems I got the fuel rack adjusted correctly as well as the valves and injector timing. After I get the fuel leaks fixed I will fill the cooling system and let it get up to temperature. Then on to bleeding the brakes, the next thing to fight to the very end.
