• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

CUCV vibration

joeyaguirre21

joeyaguirre21

Member
65
0
6
Location
el paso, texas
Good evening gentlemen. From west Texas.
I'm having a problem with my 1984 CUCV. I was driving down the highway and all of a sudden I started to get a bad vibration in the drivetrain, I check my motor mounts and they checked out good. I disconnected the torque converter, started it and still has the vibration. This vibration is with the vehicle on park or neutral and idle or any RPMs. I think is coming from the motor. I took the water pump plate off to check the chain and the chain seems alright but not to sure. Also when all this started I noticed the injection pump is now leaking and never was before until the vibration. I'm clueless up until this point.
 
doghead

doghead

4 Star General /Moderator
Staff member
Super Moderator
Steel Soldiers Supporter
26,246
1,179
113
Location
NY
Does your harmonic balancer look ok? They do separate/shift with age.
 
Curtisje

Curtisje

Well-known member
Steel Soldiers Supporter
596
693
93
Location
Okinawa, Japan
TM9-2320-289-34, page 2-18,
21. IDLES ROUGH WITHOUT ABNORMAL NOISE OR SMOKE, WILL NOT CLEAR UP
Step 1. Check fuel injector pump timing. (See paragraph 3-44)
Step 2. Test each fuel injector nozzle. (See paragraph 3-36)
Step 3. Remove governor cover. (See paragraph 3-38) Check for black particles.
If black particles are evident, replace governor weight retaining ring. (See
paragraph 3-42)
Step 4. Test fuel injector pump, (See paragraph 3-44)
Step 5. Test compression of each cylinder. (See paragraph 3-2)
 
Last edited:
D

dependable

Well-known member
1,720
188
63
Location
Tisbury, Massachusetts
Leaking injection pump line(s) would cause a pretty good vibration if leaking enough that the cylinder won't fire.

Not sure what you mean by disconnecting torque converter. Did you unbolt it from flex plate?
 
joeyaguirre21

joeyaguirre21

Member
65
0
6
Location
el paso, texas
Curtisje said:
TM9-2320-289-34, page 2-18,
21. IDLES ROUGH WITHOUT ABNORMAL NOISE OR SMOKE, WILL NOT CLEAR UP
Step 1. Check fuel injector pump timing. (See paragraph 3-44)
Step 2. Test each fuel injector nozzle. (See paragraph 3-36)
Step 3. Remove governor cover. (See paragraph 3-38) Check for black particles.
If black particles are evident, replace governor weight retaining ring. (See
paragraph 3-42)
Step 4. Test fuel injector pump, (See paragraph 3-44)
Step 5. Test compression of each cylinder. (See paragraph 3-2)
Click to expand...
Do you have the link to those troubleshooting procedures
 
cucvrus

cucvrus

Well-known member
11,474
10,437
113
Location
Jonestown Pennsylvania
joeyaguirre21 said:
Yes, its brand new and replaced exactly a year ago
Click to expand...
New does NOT always mean better. Was it replaced just to replace it? Or was it actually bad? If it were bad is it possible that the damage was done at that time? And I do agree with a weak cylinder or misfiring delivery nozzle. Remove the nozzles and have them tested with a pop off tester. May not be the real name but a diesel shop I use checks mine on occasion if I have the engine apart. And like I say if you replace the balancer just to replace it you could be putting an inferior part on the vehicle. Good Luck. Be Safe.
 
joeyaguirre21

joeyaguirre21

Member
65
0
6
Location
el paso, texas
cucvrus said:
New does NOT always mean better. Was it replaced just to replace it? Or was it actually bad? If it were bad is it possible that the damage was done at that time? And I do agree with a weak cylinder or misfiring delivery nozzle. Remove the nozzles and have them tested with a pop off tester. May not be the real name but a diesel shop I use checks mine on occasion if I have the engine apart. And like I say if you replace the balancer just to replace it you could be putting an inferior part on the vehicle. Good Luck. Be Safe.
Click to expand...
I PUT A NEW GOOD BALANCER ON THE ENGINE AND DIDN'T START HAVING PROBLEMS UNTIL WHEN IT STARTED VIBRATING
 
M

Miah

Member
90
29
18
Location
Kansas City-ish, MO
Err yes, something starting to vibrate would definitely be when you started noticing a problem. I believe his point is don't automatically write it off because you put something new on so it "can't" be bad. A person can't discount their new parts being bad, or simply failing prematurely. In this day & age where so much is outsourced & corners are cut for maximum profit anything can happen.

This is a human failing that all of us have to deal with. Play it safe & do a careful inspection of it for the sake of being thorough. Doesn't hurt even if it is less likely than a failure elsewhere
 
D

dependable

Well-known member
1,720
188
63
Location
Tisbury, Massachusetts
As long as you have TC held back, its OK, we know it slides easily on tranny input. Seems like a unconventional diagnostic step though, as cracked flex plate or loose bolts easily seen by visual inspection.
 
cucvrus

cucvrus

Well-known member
11,474
10,437
113
Location
Jonestown Pennsylvania
My concern now is pushing the dirt build up that is on the converter center mount back into the front pump seal. Seems to me as it would create a new problem. Far be it for me to suggest that happening. Anytime I must change a flex-plate with the transmission in place I very carefully clean that center shaft area as good as I can. Good Luck. I hope this all works out for you.
 
You must log in or register to reply here.
110,926members
165,351threads
2,326,671posts
1,634online users
Top
✖
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks