-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
mep803 power conection
- Thread starter mchlsprgn
- Start date
- 3,823
- 5,923
- 113
- Location
- MA
Give us some details on what you are trying to do? 120V or 240V? Do you have a generator hookup now, or how are you planning on getting power into the dwelling?
I have a panel next to the gen thats connected to my house. It's hot al the time unless the power is off I'd like a disconect at the gen also I would like to cover gen cabel outet I'm running 240 volt . There are breakers in the panel to turn off or on gen
Scoobyshep
Well-known member
- 1,126
- 1,489
- 113
- Location
- Florida
There are 2 real flavors here, you can install a transfer switch before the panel or an interlock in the panel. For the interlock to be an option you need a main breaker in that panel.
- 114
- 208
- 43
- Location
- Fredericton, New Brunswick, Canada
Just finished setting up for 220v manual transfer - main switch to give me option to provide backup power to house or shop. - Shop Sub panel , -feed to house - Interlock at shop and house panel. 803A unbounded. ( LOTS of good advices on the forum).
Attachments
Ray70
Well-known member
- 2,583
- 5,863
- 113
- Location
- West greenwich/RI
Can you walk us through your setup with more detail? Looks interesting, but a little hard to follow from the pictures.
Scoobyshep
Well-known member
- 1,126
- 1,489
- 113
- Location
- Florida
It looks like you are switching the neutral, if thats the case you may want to rethink that. Because thats where the generator needs to be bonded.
- 114
- 208
- 43
- Location
- Fredericton, New Brunswick, Canada
K I'll break it down main wire is teck90 6/4 ( 1 red,1 black, 1 blue , 1 bare copper) ( using blue wire as my white neutral) . Power from 803 first goes to double throw switch. ( I can choose to power house backup or shop sub panel)
Attachments
- 114
- 208
- 43
- Location
- Fredericton, New Brunswick, Canada
2 - if the double throw switch is on house it goes to the main panel who was already wired for genset with interlock ( feeds the house backup)
Attachments
- 114
- 208
- 43
- Location
- Fredericton, New Brunswick, Canada
3- if double throw switch is on shop it feed subpanel in shop. Subpanel is fed by main panel or genset. Interlock for safety
Attachments
- 114
- 208
- 43
- Location
- Fredericton, New Brunswick, Canada
The blue wire is in fact my white neutral , the main interlock to feed house is GFI protected that why white(blue) red and black on breaker.
If I screwed up , feedback is welcome
Scoobyshep
Well-known member
- 1,126
- 1,489
- 113
- Location
- Florida
So the shop panel is only from the generator?
Sent from my SM-G973U using Tapatalk
Sent from my SM-G973U using Tapatalk
- 114
- 208
- 43
- Location
- Fredericton, New Brunswick, Canada
House and shop are seperate building and new built . I have 2 distinct 200amps service , one feed the main panel in the house the second 200 amp service feeds the main panel in the shop. -( 2 panel in the house, main one for heat pump , dryer , heated floor ects , and a back up for fridge lights , TV wifi ects) - the 200amps main panel in the shop is set up with interlock to feed the back up panel in the house) the picture attached is the 200 amp panel set up to feed the house backup panel ( 220 orange 60 amp breaker in the middle)
Attachments
- 114
- 208
- 43
- Location
- Fredericton, New Brunswick, Canada
The shop sub panel is either backfeed from the shop 200amp via 60 amp breaker or from genset ( orange interlock)
Attachments
Scoobyshep
Well-known member
- 1,126
- 1,489
- 113
- Location
- Florida
the important takeaway is making 2 feeds cant be crossed and each live feed is connected to a neutral bond
- 114
- 208
- 43
- Location
- Fredericton, New Brunswick, Canada
Thanks, just to confirm does this looks ok to you. ? The way I'm setup. The genset can't backfeed the panels as their is an interlock on both side of the double throw switch. And the genset neutral is is engaged on both side regardless?
Scoobyshep
Well-known member
- 1,126
- 1,489
- 113
- Location
- Florida
Ok , so the generator feeds into the double throw, which feeds the house OR the shop interlock? Both of which are switching their respective neutrals?
- 114
- 208
- 43
- Location
- Fredericton, New Brunswick, Canada
Correct
Scoobyshep
Well-known member
- 1,126
- 1,489
- 113
- Location
- Florida
Complex setup, but it serves your needs. Looks pretty good, keep in mind a backfeed breaker (breaker feeding the buss) cant rely solely on being a snap in. By code they heed an auxiliary retaining means. simple fix, add a tiewrap around the breaker and the one opposite it.
robson1015
Active member
- 515
- 132
- 43
- Location
- New Concord, Ohio
What kind of interlock is that ??? Looks like a button cap with a flat spot...?