• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

Question on aftermarket parts and fitment

beerthirty

Member
47
7
8
Location
iowa
Is there a list of aftermarket parts that fit on the drivetrain and suspension?

I most likely snapped my rear half shafts last night (or worse) when I buried my m998 up past the doors in snow. (Bad idea fairy was strong). I am mechanically inclined, just never done much on the hmmwvs before. I have a 91 M998 soft top.
Wondering if anyone has put in beefier T case, aftermarket hubs (greased vs the oil bath), pretty much anything dealing with suspension, drive train etc.

I'd assume spec wise, if I can find half shafts that are same specs but higher rating there wouldn't be a issue same with much of the rest.
 

Bulldogger

Well-known member
Steel Soldiers Supporter
1,330
585
113
Location
Quantico VA
Try the Hummer Knowledge Base for aftermarket cross-references. As far as Half Shafts, many have had good experience with those from Advance Auto / Autozone. They are the 10K versions with ABS sensor ring, which is not needed typically and some remove it.
BDGR
 

Coug

Well-known member
Steel Soldiers Supporter
2,969
4,350
113
Location
Olympia/WA
The hubs work just fine as is, and I've never heard of anyone breaking one no matter how stupid they were being. The oil bath system works fine, provided you actually check fluid level once in a while to make sure it's still filled to the correct level. I've never actually heard of aftermarket hubs for these.

Halfshafts are the weak point. This is actually a good thing, because they are relatively easy to access and easy to replace.

The autozone shafts are imports, chinese made. For the price and lifetime warranty you can't go wrong if you don't mind chinese made parts, otherwise stick to one of the main parts distributors like MacMotors, Kaskar, HPG, or the AM General website.

Other than that, if you want to start swapping out transfer cases and differentials and such, deep pockets and good fabricating skills are kind of a necessity.
 

Ajax MD

Well-known member
1,569
1,414
113
Location
Mayo, MD
That's definitely what likely happened.
To prevent this from happening in the future, read up on BTM: Brake Throttle Modulation. While common in the off-roading world, it's an essential technique for HMMWV operation:

 

beerthirty

Member
47
7
8
Location
iowa
Firstly, we definitely were not driving properly. I got it fully knowing offroading/driving through my cornfield etc was going to likely break shit.

Finally got time to look at it. And at the moment it looks like it'll be some knuckle busting fun as the V belts are all out of their grooves and way worn out (1 was completely broke) grabbing some tomorrow and hopefully the guys are done hooking up the vehicle lift so we can start looking at the underside to figure out what we broke in that area.
 

Attachments

beerthirty

Member
47
7
8
Location
iowa
To prevent this from happening in the future, read up on BTM: Brake Throttle Modulation. While common in the off-roading world, it's an essential technique for HMMWV operation:

Thanks for the post definitely worth the read. Drove hmmwvs for 10 years in the military never once was told this. Probably should've been common sense but I'm not exactly a rocket scientist when it comes to 4x4 type stuff
 

beerthirty

Member
47
7
8
Location
iowa
Why does it look like the belts are on inside out?
Because they jumped off when we were being idiots apparently. Had to order the alternator belts. Got it all put back together.

Started it up sans alternator belts and putting it into R or any drive theres a loud clunk after a few minutes and the front is the only ones spinning. Back end tires move when we towed it a few feet to push snow but otherwise only the front end spins.
 

TOBASH

Father, Surgeon, Cantankerous Grouch
Steel Soldiers Supporter
Supporting Vendor
3,569
3,475
113
Location
Brooklyn, NY
Engine works so worse cast scenario is a new transfer case or driveshaft or differential.

Maybe a little less beer and a little more behaving older than 30 in the future?
 

beerthirty

Member
47
7
8
Location
iowa
If I can figure out how to upload videos on imgur or what not I'll upload tonight.
Messing around for a few minutes, the minute the front tires meet resistance it seems like the transfer case pops out
 

TOBASH

Father, Surgeon, Cantankerous Grouch
Steel Soldiers Supporter
Supporting Vendor
3,569
3,475
113
Location
Brooklyn, NY
If I can figure out how to upload videos on imgur or what not I'll upload tonight.
Messing around for a few minutes, the minute the front tires meet resistance it seems like the transfer case pops out
it might be as simple as the cable needs adjustment.

it might also need a replacement or rebuild.
 

beerthirty

Member
47
7
8
Location
iowa
Engine works so worse cast scenario is a new transfer case or driveshaft or differential.

Maybe a little less beer and a little more behaving older than 30 in the future?
I was sober when we went out. That's the worse part lol you'd think my common sense would be not to drop off into a non maintained road lol
 

TOBASH

Father, Surgeon, Cantankerous Grouch
Steel Soldiers Supporter
Supporting Vendor
3,569
3,475
113
Location
Brooklyn, NY
What cable? Tow cable maybe, CAMO
The X-fer case shifter mechanism cable/rod/thingy/doo-dad

Surprised you don’t know that TM lingo. You need to search the index and appendix better.
😉
 
Last edited:
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks