LIFEISGOOD
New member
- 7
- 0
- 1
- Location
- Wisconsin
Could someone help this old timer get to the bottom of why my percent of rated current gauge isn’t registering
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Percent of rated current
- Thread starter LIFEISGOOD
- Start date
You mean the voltage gauge in the upper cluster? Do you have a 24 volt system still? 2 alternators etc...if so I assume the starter is still 24 volt...if that works you can check the plug that comes out of the gauge for 24 volts...if you have that there a resistor on the back of the guage is probably burned out. If I remember right it is a 300 ohm. Use a multimeter on the plug of the guage don't use the body as a ground.
Sent from my SM-S906U using Tapatalk
- 3,827
- 5,934
- 113
- Location
- MA
Does your voltage gauge register, or is that also not working?
- 2,145
- 3,526
- 113
- Location
- Pepperell, Massachusetts
For starters, model generator are you working on?
Ray70
Well-known member
- 2,592
- 5,905
- 113
- Location
- West greenwich/RI
I went back and re read like 4 times trying to figure out if I had missed something.....LIFEISGOOD
New member
- 7
- 0
- 1
- Location
- Wisconsin
Yes it is in the top cluster, left of “Percent Power“ gauge
this unit is an 804A seems to run quite well and have load banked it on a diy load bank made of 120v and 230v water heater elements at 100 percent reading on the percent power gauge but percent rated current gauge doesn’t budge. I replaced the gauge hoping that’s all it would be but I was wrong
LIFEISGOOD
New member
- 7
- 0
- 1
- Location
- Wisconsin
And yes it is 24volt system
Sorry I thought I was in the cucv section! Phone doesn't show it to easy. Disregard.
Sent from my SM-S906U using Tapatalk
Ray70
Well-known member
- 2,592
- 5,905
- 113
- Location
- West greenwich/RI
Do you have the TM's for your machine?
I may be mistaken, but I think ( like the 004-007, it may only function when paralleling 2 units together.
% power works in standalone and % Current in parallel.... perhaps, but the TM will tell you for sure.
I may be mistaken, but I think ( like the 004-007, it may only function when paralleling 2 units together.
% power works in standalone and % Current in parallel.... perhaps, but the TM will tell you for sure.
LIFEISGOOD
New member
- 7
- 0
- 1
- Location
- Wisconsin
I ll see if I can track down the TM for this and I appreciate all you gents pointing me in the right direction It never dawned on me that this could be related to the pairing of two units Thank You
- 2,145
- 3,526
- 113
- Location
- Pepperell, Massachusetts
According to the -10 TM it should display readings regardless if it's running stand alone or in parallel.
Stand alone operation...
Stand alone operation...
Last edited:
Ray70
Well-known member
- 2,592
- 5,905
- 113
- Location
- West greenwich/RI
That's the % Power meter, his issue is with the current meter.
The TM is available right here on this site, go to the top, click on TM then get to the Generator section and then find your machine.
The TM is available right here on this site, go to the top, click on TM then get to the Generator section and then find your machine.
- 2,145
- 3,526
- 113
- Location
- Pepperell, Massachusetts
Good catch Ray.
The same is true for the current meter.
I updated my previous post.
The same is true for the current meter.
I updated my previous post.
- 16,755
- 24,060
- 113
- Location
- Burgkunstadt, Germany
6. Ammeter (PERCENT RATED CURRENT) Indicates generator set load current as a percent of rated current.
And yes, under load it should work.
And yes, under load it should work.
LIFEISGOOD
New member
- 7
- 0
- 1
- Location
- Wisconsin
I appreciate the help youve provided and I have scoured through the TM’s until my eyes hurt but I can’t seem to find any way of checking the function or a fault leading to no meter reading
- 2,145
- 3,526
- 113
- Location
- Pepperell, Massachusetts
-24 TM paragraph 2-29
LIFEISGOOD
New member
- 7
- 0
- 1
- Location
- Wisconsin
I very much appreciate your help Thanks