ida34
Well-known member
- 4,120
- 35
- 48
- Location
- Dexter, MI
Where can I get connectors for my deuce? I need to wire some stuff and want to keep it original equipment looking.
Chuck
Chuck
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Where to get packard connectors?
- Thread starter ida34
- Start date
Dieselsmoke
New member
- 1,146
- 2
- 0
- Location
- CA/NV
I see them pop up from time to time on Ebay.
ida34
Well-known member
- 4,120
- 35
- 48
- Location
- Dexter, MI
Are they listed as packard connectors on ebay?
Chuck
Chuck
- 7,062
- 153
- 63
- Location
- Mid Hudson Valley NY
Saturn Surplus.
Dieselsmoke
New member
- 1,146
- 2
- 0
- Location
- CA/NV
I usually find the listed under military vehicle parts
- 7,584
- 365
- 83
- Location
- Cheyenne, WY
yep, saturn surplus is where I got mine awhile back.
- 10,350
- 92
- 48
- Location
- Meadows of Dan, Virginia
I can sell you one of these bundles for $20.00, shipping included.
It has about 100 ft of 16G hypalon jacketed wire plus Packard connectors and molded splitters as shown in the diagram below.
I use them all the time, just cut and splice the wires, no need to assemble the connectors and the splitters are very handy.
Only have a few left. PM me with if interested.
It has about 100 ft of 16G hypalon jacketed wire plus Packard connectors and molded splitters as shown in the diagram below.
I use them all the time, just cut and splice the wires, no need to assemble the connectors and the splitters are very handy.
Only have a few left. PM me with if interested.
Attachments
ida34
Well-known member
- 4,120
- 35
- 48
- Location
- Dexter, MI
Ok Bjorn I am in for $20 for one set. How do you want payment? Were these the blackout kits I saw on ebay a while ago? I also wanted to say I enjoyed your article on bio-diesel and wvo. I plan on trying to make bio-diesel in the next year. My wife thinks I am nuts but I now want to go diesel on all my vehicles. I figure on getting a cheap diesal Mercedes and a CUCV for my daily driver. It seemed complicated at first but your article and some others I saw made the fuzzy picture come into focus.
Thanks
Chuck
Thanks
Chuck
Armada
New member
- 3,046
- 4
- 0
- Location
- Buick City, MI
- 10,350
- 92
- 48
- Location
- Meadows of Dan, Virginia
Chuck, I sent you a PM.
rmgill
Active member
- 2,479
- 14
- 38
- Location
- Decatur, Ga
I would still prefer a proper assortment kit for these. That'd make my work far easier when it comes to re-wiring things. Heck, if I'd had an assortment of these, I'd have used those rather than the standard crimp on style connectors you get at autozone. Still, those shoudld work fine given I slathered on two coats of liquid electrical tape on the connectors.
I wonder if we could all get together on a bulk buy and make some assortment kits. Be nice on the road too.
I wonder if we could all get together on a bulk buy and make some assortment kits. Be nice on the road too.
rmgill
Active member
- 2,479
- 14
- 38
- Location
- Decatur, Ga
And I just found one of the companies that makes these.
http://www.amerline.com/singlewire.htm
Looks like they make the trailer, Slave and other types of connectors too.
http://www.amerline.com/singlewire.htm
Looks like they make the trailer, Slave and other types of connectors too.
ida34
Well-known member
- 4,120
- 35
- 48
- Location
- Dexter, MI
Bjorn, PM back to you. Payment sent.
Chuck
Chuck
- 10,350
- 92
- 48
- Location
- Meadows of Dan, Virginia
Thanks Chuck, your wire harness will be in the mail later today.
Ryan, the beauty about the harnesses I have is that the crimping is already done, I just cut and splice the wires with the connectors as needed. The splicing can be done with any of several standard methods. Also, the "splitters" are the greatest, molded one wire in two or three wires out (see diagram above).
If you buy Packard connectors in bulk you will need all parts of course and a crimping tool for these particular terminals.
The hypalon jacketed wire is also original.
Don't you all come calling at once, I only have a couple of them left.
Have a great day!
Ryan, the beauty about the harnesses I have is that the crimping is already done, I just cut and splice the wires with the connectors as needed. The splicing can be done with any of several standard methods. Also, the "splitters" are the greatest, molded one wire in two or three wires out (see diagram above).
If you buy Packard connectors in bulk you will need all parts of course and a crimping tool for these particular terminals.
The hypalon jacketed wire is also original.
Don't you all come calling at once, I only have a couple of them left.
Have a great day!
- 10,350
- 92
- 48
- Location
- Meadows of Dan, Virginia
Added PS Magazine info on the Packard connectors:
http://steelsoldiers.com/modules.ph...ame=gallery&file=index&include=view_photo.php
http://steelsoldiers.com/modules.ph...ame=gallery&file=index&include=view_photo.php
rmgill
Active member
- 2,479
- 14
- 38
- Location
- Decatur, Ga
I'd rather not have to splice wires. Run a continuous wire to a connector. I don't mind splicing in at a single point a bunch of wires, but that preference is for the ends at the lights and components I've added so I can remove individual components.
ie I'd prefer
Light----wire-----Connector >] Connector -----wire-------termination.
Rather than
light ------wire---splice----wire----connector>]Connector----wire----splice----wire-----termination
ie I'd prefer
Light----wire-----Connector >] Connector -----wire-------termination.
Rather than
light ------wire---splice----wire----connector>]Connector----wire----splice----wire-----termination
Dieselsmoke
New member
- 1,146
- 2
- 0
- Location
- CA/NV
- 10,350
- 92
- 48
- Location
- Meadows of Dan, Virginia
Hey Chuck, did you receive yours yet?
The vinyl tape comes off real easy and doesn't leave any residu.
The splitters saves a lot of hazzle and makes for a more reliable wiring.
Don't know where one could find those individually for that matter...
When you rewrap your harness, get a quality black vinyl tape, it makes a difference.
Spend like $5 for a roll of Scotch/3M Super 88 or similar.
For cable ties, use the black UV resistant kind only, unless you are covering it with the vinyl tape.
The vinyl tape comes off real easy and doesn't leave any residu.
The splitters saves a lot of hazzle and makes for a more reliable wiring.
Don't know where one could find those individually for that matter...
When you rewrap your harness, get a quality black vinyl tape, it makes a difference.
Spend like $5 for a roll of Scotch/3M Super 88 or similar.
For cable ties, use the black UV resistant kind only, unless you are covering it with the vinyl tape.
ida34
Well-known member
- 4,120
- 35
- 48
- Location
- Dexter, MI
I did get them the other day. Now I need someone to turn up the heat outside so I get all these Deuce projects done.
Chuck
Chuck
clinto
Moderator, wonderful human being & practicing Deuc
Staff member
Administrator
Super Moderator
Steel Soldiers Supporter
Supporting Vendor
- 12,597
- 1,138
- 113
- Location
- Athens, Ga.
I considered creating a new thread for this, but since it had already been covered, I'll try it here.
About the cheapest I have found new Packards is Erik's, but man, the cost is adding up fast when doing projects like backup lights and side markers.
1. Does anyone have a source for bulk purchases at steep discounts? I'd buy a thousand (12/14ga male/female) if I could get them cheap enough, then I'd sell the excess.
2. Anyone want to go in on a group buy?
Thanks
C
That link is now obsolete, superseded by: http://www.amerline.com/MSSingleWire.html
Last edited: