wsucougarx
Well-known member
- 6,951
- 67
- 48
- Location
- Washington State
Joe's a good guy. Wish I had enough funds to buy one.
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
2010 PNW Mini - Rally
- Thread starter srodocker
- Start date
kurtkds
Member
- 629
- -1
- 18
- Location
- Puyallup, WA
I have a set in the trailer ready to go to the meet.
jesusgatos
Active member
- 2,689
- 28
- 38
- Location
- on the road - in CA right now
Yeah, he's really hooking me up. Been a great guy to deal with. Speaking of that LDS, is there any chance we'd be able to transfer that engine/crate from a trailer into the back of my pickup truck? Joe's lift can only get it up about 2ft off the ground, and my truck bed is about 3.5ft. Just wondering if that might be an option. Don't know if Joe can even bring it to the rally.
I might need to bring a trailer anyway, if MilitaryRestoration has the riveted wheels that I need. Actually, in case he doesn't, maybe I should ask. I've got a bunch of Firestone T831's that I'm going to run singled on Mah Deuce, and I'm thinking that my best option for wheels right now might be re-centered stock wheels. But I need to trade my welded wheels for riveted ones. So I've got 11 wheels/tires (9 with great tread, 2 that were on the front show a little wear, and 1 spare that has good tread but shows some signs of cracking) that I'd like to trade for riveted wheels. As long as the wheels are in good condition, I don't care about the tires (would actually prefer to get bare rims).
Great, thanks!
Last edited:
jesusgatos
Active member
- 2,689
- 28
- 38
- Location
- on the road - in CA right now
Cool. Looks like I just found a fuel tank...
srodocker
Well-known member
- 6,549
- 69
- 48
- Location
- Lacey, Washington
see there ya go! 
you driving the deuce up?
you driving the deuce up?
jesusgatos
Active member
- 2,689
- 28
- 38
- Location
- on the road - in CA right now
No, it's a 2000-mile trip for me, so I'm going to borrow my brother's Gnar-Ram. Next time I'll have Mah Deuce up that way it'll have an LDS in it and a bunch of new parts though. Can't wait to get it back on the road. It's been down for a while now, as I've been going through it and rebuilding/servicing the drivetrain.
Hammer
Well-known member
- 1,483
- 398
- 83
- Location
- Winlock, WA
Hey, I did the trip with two vehicles from N Ca for last years convoy
jesusgatos
Active member
- 2,689
- 28
- 38
- Location
- on the road - in CA right now
What's up Ed? I've already racked up about 4000 miles on your old M109. Great truck. But I'm still not finished with this motorhome conversion, and I'm on work-mode until it's done. Are you going to be at the rally this year?
Angus
New member
- 27
- 0
- 0
- Location
- Renton, Wa.
I think its sold. Is it Mike?
wsucougarx
Well-known member
- 6,951
- 67
- 48
- Location
- Washington State
PMing you Joe
Hammer
Well-known member
- 1,483
- 398
- 83
- Location
- Winlock, WA
Jesse, glad you have been enjoying that beast. It sure will be a nice setup with that LDS in there!
Looks like I might make it to this mini rally!
I am at exit 71, so I am up for the convoy up there. And if Brad has a spare trans for my 5 ton, I could use another one.
I need to get another fuel cutoff solenoid for my 818 before it makes that trip though, it leaks some fuel right now as it sits.
Looks like I might make it to this mini rally!
I am at exit 71, so I am up for the convoy up there. And if Brad has a spare trans for my 5 ton, I could use another one.
I need to get another fuel cutoff solenoid for my 818 before it makes that trip though, it leaks some fuel right now as it sits.
wsucougarx
Well-known member
- 6,951
- 67
- 48
- Location
- Washington State
Ed, if you need a winch for your 5 ton he has them also
usmarines72
New member
- 65
- 2
- 0
- Location
- California
Sure could use an LDS myself.
Hammer
Well-known member
- 1,483
- 398
- 83
- Location
- Winlock, WA
I imagine he has a LOT I WANT, it is more about what I can afford right now. I am still in the process of moving, and these MV's add up when moving them all this far.
jesusgatos
Active member
- 2,689
- 28
- 38
- Location
- on the road - in CA right now
I just talked to Brad and he's got a lot of the parts I'm looking for, but he doesn't have any extra hardtops. I'm just getting ready to paint Mah Deuce and I'd REALLY like to find a hardtop before I sandblast/paint because the custom cabover rack I made makes it much more difficult to remove/install a top. Can anybody help me out?
Stalwart
Well-known member
- 1,739
- 33
- 48
- Location
- Redmond, WA
Brad showed up at the PSMVCC meeting tonight and mentioned you guys stopping by, his gates open at 7AM that morning he said. He convoyed with my Scorpion tank once 6-7 years ago, Damon and I also went down there in the HEMTT to pick up a turbine generator.
BTW, could one of you take some good pictures of the old Packard marine engine he has for sale for me?
BTW, could one of you take some good pictures of the old Packard marine engine he has for sale for me?
wsucougarx
Well-known member
- 6,951
- 67
- 48
- Location
- Washington State
Yah, I've been talking to him about our visit on the 6th. He's pretty pumped as he wants this his MV parts to go...well at least some of them. He's still holding tight to a few parts scattered here and there. I still need to join the PSMVCC. I finally got around to subscribing to Military Vehicles Magazine. Brad's been harassing me about signing up so I did.
jesusgatos
Active member
- 2,689
- 28
- 38
- Location
- on the road - in CA right now
Yeah, he told me the cityis making him get rid of all his stuff, so he's cutting up a lot of the trucks and taking 30,000-40,000lbs to the scrapyard tomorrow! What a shame.
wsucougarx
Well-known member
- 6,951
- 67
- 48
- Location
- Washington State
Well luckily that 30-40k lbs is a city garbage truck
srodocker
Well-known member
- 6,549
- 69
- 48
- Location
- Lacey, Washington
i was about to say...were coming on the 6th im sure i can tell him to hold on to a few parts while another paycheck comes in