• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

Search results

  1. jonesal

    HOL-GAR CE-106-AC/WK 9 EP Genset

    Bill, You'll find the pickup tubes are brass so a steel can will be fine. My grav setup is steel and it always makes me nervous setting it up. I don't think the old pickup fits a Spectra, but I don't bother with that new junk anyway...;) You tell us if it fits if you go that route. As far as...
  2. jonesal

    Loss of RPM after revving engine

    I have this same problem. Any chance of helping me locate where in the TMs the adjustment procedures might be? Both for idle speed and how the shut off is supposed to be adjusted ("just so") in the IP? I have a picture in my head, but some more info from the TMs might prior to diving in...
  3. jonesal

    HOL-GAR CE-106-AC/WK 9 EP Genset

    To answer your questions, I spend as little time as I can on the internet (I would rather do work than surf). I have been doing civilian and military restorations for almost 30 years so you get an idea of where the "go to" places are. Then and Now is one of them. The "sucking" fuel pickup...
  4. jonesal

    Winter Dress

    Now that spring is here, here are some pics of the Deuce in winter dress. The winterization blankets work ...ok. I think they help when it's below zero, but it's not a huge help. I would think the winterization heater for the powerplant would be the very best to have... which I cannot afford...
  5. jonesal

    HOL-GAR CE-106-AC/WK 9 EP Genset

    One last comment. Your C3 TM is setup for the "standard" 25 amp dc generators and regulators. My genset (and another guy's I've been emailing) is the 19 amp model. The 19 amp model is a two wire from the dc generator (verses the 3 wire for 25 amp) and it's 1 wire to the battery (verses 2 out...
  6. jonesal

    HOL-GAR CE-106-AC/WK 9 EP Genset

    And here's a video.
  7. jonesal

    HOL-GAR CE-106-AC/WK 9 EP Genset

    OK, the vendors name is "Then and Now". If your fuel pump is stock, it will be a Delco. On the base that mounts to the engine, will be a number that is stamped. That is the model number and they will need that to send you the right kit. Here is their URL: Fuel Pump Rebuilding Kits - Then And Now...
  8. jonesal

    HOL-GAR CE-106-AC/WK 9 EP Genset

    I'm still looking for the vendor's name, sorry it's taking so long. How many pages is the -20 C3 manual? I am having trouble with the regulator and the regular -20 manual has the wrong one in it. I would love to get my hands on that section. I have only scanned about 10 pages from the -35...
  9. jonesal

    HOL-GAR CE-106-AC/WK 9 EP Genset

    Bill, A rebuild kit is available for the fuel pump. I rebuilt mine and it was easy. The kit comes with the one way valves, diaphragm, gaskets, screen, etc. A nice kit for $35 for your exact pump. It even has a modern diaphragm that will not degenerate in modern gas. I will try and dig up...
  10. jonesal

    HOL-GAR CE-106-AC/WK 9 EP Genset

    Hey, nice generator!!! It's a keeper. The safety switch builds up heat in the resistor that pops the bimetal switch. Ya, if you figure it out, let us know... so that we know. It was a mystery to me too. there are lots of modern therm-o-disk switches on eBay that you might be able to use. Just...
  11. jonesal

    HOL-GAR CE-106-AC/WK 9 EP Genset

    Bill, Sorry for the delayed response --> traveling for work. If you get a response from therm-o-disk, post it here. I called them many times and never got one ounce of satisfaction. Good luck. That being said, you can take the safety switch apart, clean it, and it will probably work unless...
  12. jonesal

    HOL-GAR CE-106-AC/WK 9 EP Genset

    The stock carb rebuild kit is still available at your FLAPS. The only difficult part to find is the governor spring on the throttle shaft, but other carb springs will work (and that's what I had to do). There are several very close TSX NOS carbs on eBay if you need one that are close enough to...
  13. jonesal

    HOL-GAR CE-106-AC/WK 9 EP Genset

    Check your flame switch to see if it's stuck (will require disassembly). Also check the on off winterization switch behind the operators panel. The fuel regulator in attached/inside the winterization unit. The device you are referring to is the electric fuel pump for the winterization unit...
  14. jonesal

    HOL-GAR CE-106-AC/WK 9 EP Genset

    Oh yes, it got the full banana. The winterization system is essential for its rated start at -65 F (thats 65 below zero for you southlanders). The motor, fuel pump and combustion switch were easily refurbished. However, I could not find parts for the fuel regulator valve (diaphragm mostly). I...
  15. jonesal

    HOL-GAR CE-106-AC/WK 9 EP Genset

    Thanks for the comments. I'm starting to gather that there aren't a lot of restorers on the list. I learned a fair bit on this project as I hadn't worked with three phase for awhile. It was very interesting to see how the designer implemented single and three phase from 120 to 240 V into one...
  16. jonesal

    Difference Between AMA-5104UT and AMA-5102UT

    As the title line reads, what's the difference between the AMA-5104UT and AMA-5102AT alternators? From what I can tell the 5104 is the newer version of the 5102. I have the 5104 and see that all the TM's are for the 5102. Any leads on the TMs for the 5104? I tried LOGSA with no luck. Who sells...
  17. jonesal

    Top plate for winch

    I used a structural c channel with very similar dimensions to the stock deformed channel (except much thicker) and it works fine. Drilling the holes for the mounts was a bit of a challenge and you have to tap all the little holes for the data plates. I even tested it to see if it would shear...
  18. jonesal

    Troubleshooting a miss

    For the uninformed, can you expand on what the droop screw is and what it does? I missed that one in the TM. Thanks, jonesal '70 M35A2
  19. jonesal

    New Member from South Dakota

    deuceman51, I'm in Brookings as well. I agree, let's do a MV meet, no matter how small this summer. I would be great! Thanks, Allen Jones '55 M38A1 '70 M35A2
  20. jonesal

    H-161 Headset Ear Cushions

    I need new ear cushions for my H-161 headsets. I've checked the archives... vendors I know of... and even called the manufacturer ($150 minimum order). A Astrocom 10215 (5965-00-815-2525 or 5965-00-058-1246) or Radiolabs TC 182 D335-1 are what are worn out. I don't want the fabric ones (like...
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks