Search results

On my 1078A1, when I roll a passenger window up, the gasket rides up with it. Any ideas where I would be able to get replacement gaskets that have tabs in place and are nicely playable?

I think the plan is to refurbish the existing starter and get another one if reasonably priced. Is the M0017705ME, which I have, interchangable with the M0017730ME ?

Its 3126.., her is the image from the starter .

Thanks for all the good info. Mine is LMTV 1078A1, which, I think is the C7, so trying to figure out what starter to get. Would this $300 one work:? http://vi.raptor.ebaydesc.com/ws/eBayISAPI.dll?ViewItemDescV4&item=362700899170&category=177699&pm=1&ds=0&t=1568280719000&ver=0

Thanks for info and helpful hints for installation. When removing starter do you take off the front wheel for better access?

To get my M1078-A1 start I had to tap the starter with the rubber mallet .. My conclusion the starter is bad. Should I replace it , or maybe there is a way to refurbish it?? How do you go about replacing the starter,it seems super heavy and I do not have a very good access to it, maybe I need...

I got a KIT too, but I think I might be able to re-use the "siren" hookup up for electircal partially on my LMTV. The part I do not understad is the mechanical one.., how to attach the LED lights. I have openings about the size of the light, but there is no backing to drive the screws into...

I got generator working ( after I opened the glued lid) and started to test the K1 switch.., the issue was that I did not know how to operate my new volt meter, there is a subswitch to turn for alternate current.... Well at least I learned bit more about the generator...,, sorry about that...

Weather got better, so I could return to the CTIS troubleshooting. The air pressure was good in the system and the CTIS, however , the CTIS system was acting erratic.., mostly solid blinking, but sometimes went to solid HWY mode. I had a new NOS CTIS controller, so I did put that in and CTIS...

Thanks, sorry you are right its a good sized metal plate. which has the weights etc... I just called it sticker, sorry..

Thanks for poinint a door sticker. That said called a friendly WA DOL office and was told that we can change the class ( and has to be a minimum of 150% of the empty vehicle weight) but its not going to lower the $247 fee..

The WA state licensing did put for my LMTV 1078 A1 in a Gross Vehicle Weight Rating Code: Class 8 - 33,0001 punds and more. Which resulted in $308 Tab fee, which most off it is $247 Gross weight fee funds road, ... improvement Is it classified correctly? My guess just scanning the follow table...

Good points about the policy and reimbursments ( Next time I will try the re-imbrusment route, nothing to loose..). I did read the policy and to me it seems the AAA policy has a paragraph that explicitly excludes the "non RV" LMTVs from the policy. The queote follows: "Box vans, cube vans...

Yeah, I was broke, and AAA refused the coverage in WA. They asked for the make and after that for weight. They would call for me a support, but would come out of my pocket. I do have AAA RV coverage..

In WA the AAA with my premier membership is refusing the tow of LMTV, did ring SAM and they said they would not cover it either.. So another option would be good.

Can I :)? Is it going to work? I have 2003 LMTV 1078A1 with the LED panel switch, some of the LEDs do not light up, some of rubber buttons are kind hard to deal with due to age. Can I go back to the mechanical switch, which will run me new $100 with shipping instead of the $300+ LED one...

Thanks for pointing to place in manuals and potential cultprint. I will test the three phase mode first and than will try to follow to relay/K1 circuit troubleshooting steps and report.

I have a similar problem with a standalone trailer mounted MEP802A , no power at lugs, but have power at the convenience outlet. I have it setup on L3-LO on panel and on inner panel on 120V/1PH I did close the AC interrupter switch.. Checked CB1 and FU1 ( for resistance) and under power. ( I...

I got the wipers and horn working. I think I fixed them last time when I replaced all the CBs. I just need the new wiper blades. Only thing that is not working is CTIS .. :).. I was troubleshooting the the 3x4 connectors and was not able to figure out what they are for. I toned them to...

My wipers, horn and sprayer are not working. I am pretty certain the reason for that is that the plastic connector with 3x4 connector holes (under the control panel) is disconnected. I think that is one of the two connectors from directional control arm ( note my turn signals, light switches...