Search results

covers Hi When the CUCVs got to the National guard level, they were instructed to take the bow kits and cargo covers off od the M880s and install them on the CUCVs. I have put 880 and CUCV covers on my M880 and they both fit about the same. And yes they flap pretty good going down the road...

mufflersOkay They went up since i bought mine, a few years ago. Still cheaaper than the $500. somebody posted :!: Ernie

muffler Hi Try Jeff at Frontline MV in Pa He had them for less than $100. 717 252 4489 Ernie

IHC amb Hi The Boyertown auto museum in Boyertown PA has a complete restored unit on display. The rear body is wood and was made by the Boyertown body works, completely different from the standard cargo. You can go online and look up the museum at www.boyertownmuseum.org Good luck with...

M416 The M416 is the correct trailer for the M1009. The way the hitches are set up on thee Blazers is very weak. It is only a 1 inch hollow metal bar and the rear bumper that hold the pintle on. When the M1009 first came out the army had a lot of problems with the rear bumpers being ripped...

M38 Hi I do not know the exact year from your serial number. but M38s were only made from late 1950 to mid 1952. Check out the G503 web site under the M38 section. Good luck Ernie

Hi Try Dave and Donna at Weebee Webbing I think they have it 1 888 ODCLOTH Ernie

WC53 axel parts Hi For the diff assembly, if you have a bolt on inspection cover on the axel the M37 parts will not work, 8 5/8 inch ring gear If the inpsection cover is welded on, you can you the M37 diff for parts. 9 inch ring gear. You can also call Ace surplus in Victoria Texas, onwer...

carb Hi You can try Sid Beck. je is Ace Surplus in Texas John Bizal, He is Midwest Military in Minn. Or Vintage power wagons All are on line Ernie

Hi A grand for a complete rust free G506 is a good price, Grab it !!!:-P The M211s just don't have any real following, they are good trucks, built much heavier than the M35 series, just gassers with that darn auto trans. Ernie

m211 Hi The parts truck does have a pintle hook, I will see how bad to get off. There is an extra airpack, but it looks pretty grungy, I doubt if it would work without a rebuild. Ernie

oldest Hi The oldest mil i have is 2 1940 VC dodges. The oldest i have pics of i my 1/22/41 dodge WC 4 Ernie

blackwood Hi Mike You were in my town and did not visit:twisted: The best items are the winch and the wiring harness. The extra sheet metal i would like to sell with the truck. If you get near me again, give me a call 856 986 5091 Thanks Ernie

M211 Hi I plan on going to the MVPA national in Indiana in Aug, about as close as I will get to Mich. If you are going to the national I could bring it with me. The parts truck is missing the following, starter, gen, reg, manifolds, Has complete body in so so shape, has cab top bows. bed...

Hi I have listed the truck many times with no real interest. So this time i will list parts separate, if any interest please contact me. All prices listed are asking prices feel free to make offers. 1. complete nos and new wiring harness, some parts are nos some are from when Jeff Smith was...

collection Hi Massimo you collection is amazing, and the craftsmanship is top notch. Keep up the good work. Was your Hummer damageed during an air drop? Ernie

push rod Hi Rod I was warned and still droped the rod out :oops: I could not get it back in place unttil i took the mounting plate oof and packed the rod with grease. The fuel pump bolts are a real joy t :twisted: o get too Ernie

M1008 fuel pump Hi when you changed the pump were you careful not to drop the fuel pump push rod out? There is a little round psch rod that fits up into a port in the block right above the fuel pump arm. This can fall out very easly and is a royal pain to keep in place, You usually have to...

M135 Hi Dave I saw your truck as you were unhooking the batteries inside the convention. You have one outstanding vehicle, as clean as it was i would have guessed that it just came off a trailer, not a 1000 mile trip. Outstanding sir, and a very fine truck!!!!!! Ernie

106 mule Hi Nick that looks amazing :D I wish i could weld that good. Looking forward to seeing it his fall in Phili. Keep up the good work Ernie