Search results

I would also check your wires at the tailights, make sure wire#21, and #22 are plugged into the correspondinding #'s of the harness. Thats one more possibillity, but not likely for both sides, but than again you never know ;-)

That's 100% correct Kenny, its the friction that causes heat, which causes the warpage. The key is knowledge, just like anything else ;-) Most times when discussing sandblasting I assume people have a basic understanding. Just like talking about engine mods, I assume most people have the...

mouse; Don't worry about "peeing" on anyone's boots (most times I wear chest wader's) :lol: I did'nt say you "can't" warp, I said I never have because I know what I'm doing(got a few years on ya with bumpin metal) . You can warp a panel at the car wash if don't pay attention. Yup Ace has...

OK mouse; First to use "Baking Soda" you need special equipment, which cost, well let's say a bunch. I have been blasting with sand for a very long time, never warped a single piece. If you know what your doing than it's just like anything else, painting, sanding...

ColoMil (Brian) My truck was in a line of about ten, they were in the "rail" yard so I don't know if they were sold or going up for auction. There were a couple of beaters in the lot where your M109 is. I saw some M101A1 trailers, just hoping they are going to auction ;-) Juan said to tell you...

Guessing your talking about the International Kenny [thumbzup] Yup only way to go :smilewinkgrin: Spoiled I guess, only way to go... [thumbzup]

Allrighty, set me back a bit, not a bunch if you bought her on the secondary market from a dealer I know you would pay way more than then the $3510.00 I paid :smilewinkgrin: As for the switch... still tracing it..wire#16A,and 16B...Anyone have the wiring# list :confused:

Sorry about the RED X :banghead: Seems it won't let me use a hosted picture [:(!] Just the thumbs :eyes: Anyway here's a few more ;-) I should also mention that DRMO listed this as "H7" we all know what that means :rolleyes:

After two aborted trips because off the chain law over the passes, I finally picked up my new 1966 Kaiser M35A2 W/W from Ft. Carson last Thursday :hop: :freaked: I got way more than I was expecting :smile: First the guy say's do you want to look it over? I said it's a little late for...

Look'in Good Dan [thumbzup] Sure hope that little piece on your fuel pump I gave ya is working! :turn:

Todd; Ya gota love that "FORD" label [thumbzup] You must be a good welder, looks like plenty to keep you busy! Maybe a few more pics?

Right below your three lever light switch is the supply control [thumbzup]

Here in Colorado I first had Light Truck plates, they cost more than my dump truck :freaked: We don't have "Historical" plates we have "Collectors plates", just has to be 25 years or more older. Catch is you pay for 5 years up front. I now have it tagged as a "Rec Truck" plates are about a...

[dito] [^] Yup said it before, say it again, "This is the PLACE" The only thing I don't agree with is "Hobby" . It's an OBSESSION..........You will find the BEST, knowledgeable, people right here! Proud to be part of the family [thumbzup] ;-)

Much rather have a "women" :turn:

Dats only fer peoples whos donts no's hows too's spells :lol: That would be great, even the best of us make a key stroke error every once and awhile :eyes:

Airborne; You have to walk before you run..... Meaning you need to fill out your Profile and Signature which needs to include your general location...Just take a gander at all the posts and you will see how a signature should look ;-) If you have any questions just pm me or any mod, we are...

Thats a bummer Joe ! So without a export license I guess you can't sell to people in California :lol: :lol: Sorry Bill (Dieselsmoke) could'nt resist that one :turn:

Thats right on the mark Joe [thumbzup] It also applies to non export, for example a non-U.S. Citizen/National or a non-Permanent US Resident without a valid State Commerce Dept. export authorization. R4X4 as far as GSA, they might not have a EUC, but they have this in the agreement: Export...

Thanks for fixing your sig Stretch [thumbzup] You need to log off and dump the cookies from the site, then when you log in again and make your next post your signature will show the update ;-)