Search results

Yes I pulled the speed sensor and measured it on the bench. It was 9.5 ohms. Measuring thru the pass thru on the second truck the speed sensor measured 271 ohms which is in range. My center diff solenoid also measures in the 3 ohm range.

My 2001 m1078 a1 speedometer stopped working and locked into a gear. Tested the speed sensor and got 9.5 ohms at 70 degrees. My 2004 truck tested 271 ohms. Looks like I need an output speed sensor. The one located inside the transfer case. Has anyone tested the solenoid for c7...

I got it figured out. I needed an app to open the tms and diagrams. Thanks

I tried to download and save from this site however after the download I can only view page 1. When I select a different page it goes back to page one ?? Thanks for your help. Mike

That would be great! I had mine in the shop today again. Checked the c7 coil and it seems to be very low impedance also. Checked voltage to the coil was a little over 26v idle in mode. Checked the top of the coil with a feeler gauge for magnetism, none. I didn’t have my scope at home but I...

Check out our new 6061 t6 replacement striker arms. They will be available very soon. Prototypes are done and tooling / programming is finished. The cost for a pair will be 70.00 shipped USA. Quantity discounts possible. Replace yours before they break! Or keep some spares on hand for...

Hi everyone, I’ve got another project finished up. Anyone interested in updating the striker arm in your door handles? Here are a couple photos of our new 6061 t6 arms.

I haven’t got back to that problem yet. From what I’ve read it looks like the c7 solenoid is powered 12 volt. Not duty cycled? I haven’t checked yet but will when it warms up a little. I now have a second truck and can swap parts if needed. Also should have a known good electrical to compare...

Hi Schmirgel, I don’t know if you know about Eco Hubs. They replace the 2:1 gear reduction units with direct drive. I’m going to be listing Eco Hubs for sale on a popular auction site . That site I’m told has very good rates on international shipping. The listing will be for one axle, so if...

Looking for some help. I’ve downloaded the tm several times for m1078 a1 but I can’t view more than page 1? what I’m looking for is the proper position of k999 in cavity j309. On the back of the fuse/relay panel. I was repairing mouse damage on my new to me truck and my release tool dropped out...

Let me know when you’re ready. Will fix you up!

The spring would need to push against something, in this case it would be the outer hub or bolt adapter. The Delta lock is stationary and the other two pieces are turning. Not the best combination. The split collars work and work well. The amount of push or turning force that the axle nut...

I didn’t say the spacers were a feel good solution. The problem I see with spacers is that the distance between the wheel nut and the bolt adapter changes from truck to truck. Yes you can shim the inner gear to make it work. I don’t see that as a simpler solution or reducing insulation...

Spacers are not going to be available on Eco Hubs, the split collars that are current production are 1/2” thick and use a larger pinch bolt. What is in the works is what I’m calling ”Delta Locks”. They engage the fixed splines on the axle tube and the pins on the axle nut. The lock is held...

Looking good! Nice and clean, the next three will go faster.

You’re going to like them! Makes the truck so much more fun! I have great stock now and your order will ship quickly! Going out to joy ride in mine in a few minutes pre/new years fun run! Snow and rain here today but a great day to check out the back roads!

The new lock set will be available to all my previous customers at a very minimal price. It will be an option on all future kits. The program is written and a few samples should be available soon. Don’t worry we will fix you up. Once again we have had no problems with...

Hi Matthew, The thicker lock rings are available no problem. All the new sets ship with the thicker ones now. I haven’t had any problems with the thin ones. Other than a few being stripped out when installing the Allen screw. I also have a new lock plate in the works now to provide a...

I’ve got several calls into Allison and transfer case rebuilders, so far no one can provide info on c7 valve body gasket?? The exploded views don’t show c7 valve body in place or the attaching bolts or gasket if there is one?? Hope to hear something tomorrow? I have removed c7 valve body...

I checked the main on the bottom. I will test the other when I get the truck back in the shop. later today.