Search results

If they are straight, put them back in! No need to spend any money you don't have to!

Just don't try to pay for anything from him with $50 bills!!!! You will regret it for the remaining five seconds of your life!

And if you want new push rods, I can get you a set for $30 + the ride. Find someone coming to the GA Rally in October to pick them up.

Actually, I think Adam (ferro) has the record, a locomotive and nine ballast cars pulled off a barge in Norfolk with a deuce. If I remember correctly it was somewhere north of 2,500,000 pounds. Locomotive on the barge would not start, and the switch engine at the dock decided it would take a...

We found the plastic aligning tool included for the clutch/pressure plate on my RAM 2500 5.9 diesel was an exact match for the deuce clutch/PP. I suspect many medium duty ones are the same.

Texas Lighthouse Foundation in Galveston converted one into a camper with a bathroom about two years ago. Contact them for specifics. They had removed all the cooking stuff and built a 'bunkhouse' for six people, complete with a couple of roof mount air conditioning units. I slept in it for...

Yes. The board needs to be custom fitted to raise the side opening between the windshield and the engine compartment on both the driver's side and the passenger/assistant driver's side. We would use a 2 x 10 about five feet long (metric equivalent 4 cm x 25 cm, four meters long), cutting the...

Remember, with the Goat, it is best to add about 20 cm of additional side in the driving compartment between the windshield and the motor to reduce the amount of water that comes in there. And when you take it into the water: 1. Make sure all the access plates are secured. 2. Turn on the bilge...

110 gallons max in aux fuel without the placards displayed on all four sides of the vehicle per DOT.

Above first gear I don't like to let the RPM's drop below 1500, in the two higher gears I downshift between 1900 and 2000 to keep the air flowing through the exhaust (lower EGT's). YMMV.

I actually have a 312 that the tone adapter will NOT fit. But it is a remanufactured 43 with a different placement of the secondary audio plug - a somewhat rare intermediate design that does NOT fit in the canvas bags that they are generally found with. It is slated to be donated to the U.S...

That's what my M109 was doing for a couple of hundred miles before the transmission started puking oil real bad (on the way to the 2016 GA Rally). Get it checked and replaced as soon as possible so you don't mess up your transmission.

Which is why I sold my 'Ma Deuce' 12 years ago, couldn't afford to shoot it for more than a few seconds a day (with lots of days in between for my wallet to recover). It was fun while it lasted!

The M105 type generator trailers have a bed on them that is 123.5 inches long and almost 83 inches wide. Using a commercial axle to drop it a bit would make getting into and out of a lot easier and you can round the front corners if a teardrop shape is what you want.

I have been told that the 'correct' weight of the hitch point should be no more than 15 percent of the total weight of the trailer with every thing in place. More than that will make it front heavy and difficult to control. And I've been told not enough weight on the hitch point helps the...

There are no diesel fumes to ever get into the food. The way the MBU's work, there is no un-burnt fuel to give an odor (unless it is malfunctioning). I've been cooking on MKT's since 2008. If you get an MKT, you need to get all the info I've collected on how to use one from setup to tear...

Go to any truck parts place. The cover is standard. Just remember to remove the studs and sell them with the PTO (you will get more for it that way). Just use regular bolts to secure the plate. The plate, gasket, six bolts and six lockwashers should cost you less than $20.

The club's Mitsy was stolen and rolled last year, permanently damaging the cab (landed on the driver's side). It is sitting wrapped up, under a tent right now. Got really squirrily above 25 mph, which is probably why it got wrecked. Club recently bought a couple of Cushman's to replace it...

I've been on the SteelSoldiers Facebook pages and see nothing on the dates for the 2017 GA Rally, and there has been no update here. Since today is only Jan 26 and Clinto said he would put the dates up by "Friday", he's running out of January, only one Friday left - tomorrow. When people are...

Our local group has (had- long story) a Mitsubishi mini truck (Not Legal For On-Road Use), same appearance truck made in China and Taiwan, and probably a dozen other places. We got one of the Chinese clones from surplus but the injectors are bad and it will only run at an idle. We have fixed...