Search results

Just givin' this a bump

1968 Baifield Ind M274A5 for sale. Deck is flat and clean, rail has a bend over the engine and two brackets are bent at the rt ft corner. 3 tires hold air, one not so much. 125PSI compression in rt cylinder, the left has had the plug wire nut left off during it's hibernation and the wire rusted...

HMMWV top grill for the hood. These have no mesh behind them. Theses are NOT armored, just plain old aluminum. They look rough but are new, never installed. They have just been sitting and I have moved them around for the past 6 years. They need to go. $130 shipped to anywhere in the conti US...

We used that? I thought we just used a come along? But I have CRS.

The tree that pulled the light pole down across the Denali, The tree at my Daughters complex, one of them.

Yes my friend, I was spreading lies and rumors about you! Glad things have calmed down for you. My girls live in a complex at the 210 and Los Robles. They are still under evac orders just because of the smoke and ash. Shelby sent a pic of the complex pool, it is black. The inside of their...

On another note, I do have some pics to put up here of some more forward progress, but things have been a bit hectic what with the desert trip with the fam and the weather.

No, thankfully, we are good except for alot of bad smoke and ash. I was there today to load out a piece that needed to leave, and I gotta say, I live 18-20 miles NE of the compound, and the smoke was horrible. There is at least one member here that was within 2 blocks of the main part of the...

Pump rebuild kits are still available. I use a place in Weymouth Ma. Then and now automotive. Call them with the numbers off of the pump and they will fix you up. https://www.then-now-auto.com/ And, if it still has the Holley on it, if you can, find a Zenith for it, the engine runs much better...

Just in case you still do, here they are. This truck is a Marine Corps ambulance. It is painted MERDC but you can still see the crosses underneath the camo. There is no word ambulance stenciled anywhere on it and the only other markings are the USMC unit on the front bumper and registration...

Do you still need measurements? I am at the Museum now and we have a couple of those laying around.

This one is assembled exactly like yours is showing minus the washers. Hope this helps.

GPA anchor up for sale. Straight, correct, non flame cut holes in the flukes for the hold downs, $1700. shipped to anywhere in the continental U.S. Located in South El Monte, Ca. Local P/u is fine.

Thank you Sir!

Well, not really the hood, but I guess it is about it too. Do all the different variants of the HMMWV use the same hood? Is the grill in the top of the hood the same dimension? I do know that there are different grills, like armored, but are the holes in the hood the same size? Another...

If nobody chimes in, I can go pull one out of the parts pile, disassemble and take pics. That won't be until Tuesday though.

1 set of NOS, never been installed 701 L&R rear axles for the G506 series 1 1/2t trucks. These were stored in a container and have not seen light of day in +25 years. Some surface rust, but in new condition. $925.00 shipped anywhere in continental U.S, NO OVERSEAS SHIPPING, Hawaii included in...

I think these are air brakes. You might need a CDL to drive it, 26,001 LBS GVW. The bed is a bit up there, hefting tools in and out will get old, fast as well as climbing up and down. As stated above, rubber is expensive for them. I don't have much experience with L/FMTV but on the older stuff...

I think since the decals are vinyl, no clear over them. I am afraid that the paint might eat the vinyl. I would then need to start over, don't wanna do that. We will just make a cover for the operators compartment so that the controls are covered and out of the sun. Made a few more changes, but...

A LONG time ago, 3 decades mybe, there used to be one of these in Randsburg. A small mining town by CL and Edwards