Search results

So what my deuce did to me today. I took it on its and mine first maiden voyage to Grandmas for dinner about 35 min away. Found out my heater core still leaking after being repaired mine also has a dented tube from being over tightened even though I clamped after it it’s still dripping going to...

I just finished buttoning everything up new tires 395/85/20 removed the ctis installed block heater fixed heater core took it out for a ride today omg I got the 45 mph vibrate really bad I guess I just joined the club lol

I’m not a fabricator I’ll have it ruined if I tried that. The hose I’m talking about runs from the air filter to the exhaust it’s outside the truck I can’t find it

Hope you feel better soon. I currently just replaced upper and lower rad hose thermostat and gasket removed heater and cleaned out a mouse nest I got a leak in there. getting ready to install a engine block heater. It normally sits outside here in PA. I can't seem to locate a part number or...

Looks great

Ok thanks for the help

I swapped over 3 more 395/85/20 tires onto my A3 only one left. My CTIS is hooked up but the tires still lose air just like the 14.5r20 did wondering if the system is messed up or I have something else going on. the DS rear when I pulled the CTIS off to change the tire oil came out of the hose...

I just changed 14.5 to 395/85/20 used engine hoist to separate rims and put a chain around bead lock used hoist to remove then squeezed tie down and ratchet strapped it put it in tire spun lock around release strap positioned it in place and remounted wheel

Thank you so much for the help I was getting ready to order a bead lock for the 395 tomorrow AM I’ll just remove them and swap the old ones into the 395. I’ll have 5 bead locks from 395 if anyone wants them

Hello Dunkeye11 I have the same question I just picked up 395/85/20 for my m35a3 and not sure which bead locks to use, the ones in the 395 or the ones in the A3 from the 14.5R20. I have not started disassembling mine yet I want to make sure I have everything. If you got your answer please let me...

Hey guys I have seen this question asked but have not seen it answered. The TM's call for 2.6 pt of fluid for the winch, Now is that for the DS of the truck or the PS or both? My winch does not have the self level wind. I am just servicing all my fluids. And I got fluid out of both sides of the...

looking at the winch from the front its on the driver side on the bottom. The fill plug is on the top and it was square to now round but i can build onto it and get it out and re tap the hole but I want to be able to get the drain out so I can flush out and debris that falls out. The pass side...

Yea it is a hard top. with the door open it rolls up feels like its riding up in sandpaper. I roll it up the then close the door and finish rolling it up to well to be somewhat water tight lol

I have a question I installed a winch on my A2 everything works good except for the the lever you unlock to use the winch. I have to put a pipe on it to move it and it makes a crack sound when it does move. I am hoping it's from lack of use but I am nervous of that sound if that handle breaks I...

can anyone tell me what might be wrong with both my windows DS/PS when the door's are shut they are extremely hard to wind. Open the doors they are better but not good. I removed the access panel and greased and lubed the tracks etc still the same stiff.

Its not what I have done to my 5 ton. But it became a motor home to a Robin who decided to build a nest and lay four eggs on top of my rear diff. I will be nice and wont move it until their gone

I replaced all my Differential fluids and Transfers case. And greased everything. I think I will give it a bath, Then time to start painting the inside of the bed

I tried going to a straight pipe on my A2 I cut off the flanges off the old muffler and welded them to the straight pipe had to modify the top muffler bracket. It sounded great at idle. Once you pressed the pedal oh my it rattled my brain. Took my wife for a ride and she said pay the 300 for a...

Got the oil changed today, Had the wife up standing on the tire, I was handing up the oil to her teamwork.

Finished the winch and it works!!!. Now I will change the oil after work tomorrow. Then start looking at my m105a3