silverbullet72tnt
New member
- 59
- 0
- 0
- Location
- Northern NH
If I can get away with just pulling hubs, Ill go that route. You guys have been a great help
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
1953 “gasser” deuce build thread/ adventure
- Thread starter silverbullet72tnt
- Start date
RodUSMC1962
New member
- 1,138
- 9
- 0
- Location
- Northwest, Indiana
The gas engine does not have the power of a multifuel but unless you are driving in steep hills, you will not notice it, if you do you just have to gear down and sit back and wait. 
silverbullet72tnt
New member
- 59
- 0
- 0
- Location
- Northern NH
I'm planning on using the truck for hauling things around town, I have an F350 and a trailer if I need to go long distances.. More for something to just drive and enjoy and tinker with
rustystud
Well-known member
- 9,280
- 2,987
- 113
- Location
- Woodinville, Washington
Now that is the correct attitude when owning one of these older vehicles.
silverbullet72tnt
New member
- 59
- 0
- 0
- Location
- Northern NH
My two little boys think its awesome too! so thats a selling point too
Last edited:
- 3,256
- 3,353
- 113
- Location
- NORTH (Canada)
If they think its awesome, the more important consequence is that you, the dad, that buys and drives it, is immensely cool. Priceless.
silverbullet72tnt
New member
- 59
- 0
- 0
- Location
- Northern NH
how available are beds in the northeast? Or would it be easier to fab one up? they look pretty simple to make
- 9,604
- 1,493
- 113
- Location
- mid- michigan
Post a parts wanted ad and see what's close to you.
gimpyrobb
dumpsterlandingfromorbit!
- 27,786
- 755
- 113
- Location
- Cincy Ohio
You could pull the caps AND the axles from the rear. That way nothing will move except the bearings...
but the rear axles will drip gear oil all over when you pull them out.
Have a towel ready to wipe them down and you'll be fine.
silverbullet72tnt
New member
- 59
- 0
- 0
- Location
- Northern NH
Any idea what size the crank nut is on a reo gasser? I wanna put some oil in cylinders and turn motor over some before trying to start it as it’s been sitting awhile
silverbullet72tnt
New member
- 59
- 0
- 0
- Location
- Northern NH
Finally got my first deuce towed to the shop today. Started snowing hard again so didn’t dig in very far yet. It’s relatively rust free for New England. Was converted to 12v at some point, not sure if that’ll stay or not.
Got the truck from a buddy for free so I’m only in it for the tow bill, which was pretty cheap.
Its been parked for about bout ten years so I’m gonna pull the plugs and put some oil/mystery oil in the cylinders and see if it’ll turn over by hand.
Its supposed to to warm up next week so I’ll report back then.
- 10,457
- 6,530
- 113
- Location
- Camp Wood/LC, TX
Looks great for being 65 years old!!! I'm working on an ex-forestry deuce that has almost the color scheme and I kinda like it. Looking forward to updates.
- 6,986
- 2,522
- 113
- Location
- Montevideo/Uruguay
It takes a 1-7/16" socket. It's a bolt, BTW.
- 890
- 158
- 43
- Location
- Las Vegas Nevada
Don't put 2 much in you'll foul the plugs up.
- 2,053
- 2,949
- 113
- Location
- Florence, SC
Subscribed
silverbullet72tnt
New member
- 59
- 0
- 0
- Location
- Northern NH
Gonna roll it over by hand with plugs out
silverbullet72tnt
New member
- 59
- 0
- 0
- Location
- Northern NH
Anyone know if a 24v generator from a jeep is interchangeable with a deuce? The ones I found for sale list m38, m37 and m35 as fitment. I just happen to have one from an m38. But the one from the deuce is missing
silverbullet72tnt
New member
- 59
- 0
- 0
- Location
- Northern NH
Bolt is what I meant..... but thank you for the info
Crazyguyla
Active member
- 817
- 124
- 43
- Location
- Altus, OK
Generator is interchangeable, the pulley may need to be changed.
silverbullet72tnt
New member
- 59
- 0
- 0
- Location
- Northern NH
Great news! Any leads on a pulley? Is voltage regulator or anything else interchangeable? Jeep is a rot box and in non saveable shape
Last edited: