tm america
Active member
- 2,600
- 24
- 38
- Location
- merrillville in
nice job looks like that engine has alot of new parts like the intake and turbo .i wonder if it was a non turbo engine that someone put a turbo on
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
55mph detonation post mortum. . .
- Thread starter FMJ
- Start date
- 4,210
- 37
- 0
- Location
- Las Cruces, NM
It's an 1988 engine, I took a picture of the data plate. Got a couple of questions, does the PTO have to come off?, or will it come out as it did in the non-winch truck? I've only swapped motors on non winch trucks. . .
Check out the smashed air lines. . .
few more pics
Check out the smashed air lines. . .
few more pics
Attachments
tm america
Active member
- 2,600
- 24
- 38
- Location
- merrillville in
i would think you could get it out with the pto on there just gonna need to twist it a little to the side and probable take the air cleaner off the fire wall.wow what happened to the air lines and driveshaft
tm america
Active member
- 2,600
- 24
- 38
- Location
- merrillville in
hey you know they have drain plugs on the front and back of the oil pan so you didnt have to knock a hole in it to do your oil change
- 4,210
- 37
- 0
- Location
- Las Cruces, NM
Well, the connecting rod probably smashed the airlines and winch drive shaft. . . 
Lifting the motor now, more pics in a bit.
Lifting the motor now, more pics in a bit.
- 34,012
- 1,808
- 113
- Location
- GA Mountains
You can wiggle it out and in with the PTO on it. Hardest part is always the juggle to get the pan past the front crossmember (unless you have the removable one). I always like looking at your pics Ed. Never know what you will see in the background. (Dually beds etc)
- 4,210
- 37
- 0
- Location
- Las Cruces, NM
Power pack wont come out in one piece on a winch truck, I have to take the radiator out. . .
- 34,012
- 1,808
- 113
- Location
- GA Mountains
My SOP is to pull the winch. I can see where if you left it in place you would need to remove it! Coming along nicely Ed.
- 26,246
- 1,178
- 113
- Location
- NY
tx399999
Member
- 78
- 1
- 8
- Location
- Tulsa, Oklahoma
When I pulled my transmission I was able to drop it onto a furniture dolly with the PTO on top and it slid right out from the passenger side between the fender and tire.
tm america
Active member
- 2,600
- 24
- 38
- Location
- merrillville in
are you getting excited yet it's getting closer to running again every minute
- 4,210
- 37
- 0
- Location
- Las Cruces, NM
Ok, dead motor is clear, and a mess is on the shop floor. . .
Doesn't look like today will be the day. . . that winch is a PITA to get a motor out over it. . . especially by yourself
Doesn't look like today will be the day. . . that winch is a PITA to get a motor out over it. . . especially by yourself
Attachments
- 4,210
- 37
- 0
- Location
- Las Cruces, NM
More
Attachments
- 4,210
- 37
- 0
- Location
- Las Cruces, NM
More pics
Attachments
- 634
- 13
- 18
- Location
- Cordova, Alaska
Man your trucking right along. Nice shop also.
- 4,210
- 37
- 0
- Location
- Las Cruces, NM
And one last pic of the underpaid shop help. . . 
I should be able to finish this tomorrow, I hope . . .
I should be able to finish this tomorrow, I hope . . .
Attachments
Nonotagain
New member
- 1,444
- 41
- 0
- Location
- Parkville, MD
tm america
Active member
- 2,600
- 24
- 38
- Location
- merrillville in
it.s funny the crank doesnt even look hurt .looks like the rod always breaks off the pin side were there any signs of trouble or did it let go all at once
were there any signs of trouble or did it let go all at once
- 4,210
- 37
- 0
- Location
- Las Cruces, NM
it.s funny the crank doesnt even look hurt .looks like the rod always breaks off the pin side
boom!!!!!!