WildEd
Member
- 47
- 38
- 18
- Location
- Corbin,KY/Poynor,TX
I had to extend the center of the grill 3" forward to clear the condenser fan. Fabricated and installed bracket for filter/dryer 
Attachments
Last edited:
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
A/C addition underway
- Thread starter WildEd
- Start date
I had to extend the center of the grill 3" forward to clear the condenser fan. Fabricated and installed bracket for filter/dryer 
- 3,256
- 3,354
- 113
- Location
- NORTH (Canada)
That is one neat and clean install!
Sent from my SM-G950W using Tapatalk
Sent from my SM-G950W using Tapatalk
WildEd
Member
- 47
- 38
- 18
- Location
- Corbin,KY/Poynor,TX
Grill painted. Time to mount the filter/dryer.
WildEd
Member
- 47
- 38
- 18
- Location
- Corbin,KY/Poynor,TX
WildEd
Member
- 47
- 38
- 18
- Location
- Corbin,KY/Poynor,TX
Under dash evaporator unit rough mounted
WildEd
Member
- 47
- 38
- 18
- Location
- Corbin,KY/Poynor,TX
Bad news for me. Reverse, 2nd and 5th gear positions of shifter hit the underdash unit even with supplied brackets maxed out. Options are to offset unit to the passenger side and fabricate brackets, or alter shifter dimensions and angles.
- 434
- 206
- 43
- Location
- Lynchburg, VA
Dunno if it helps you, but when I ran into this issue with my M37 (shifter encounter the dash after mods), I heated the shift lever up with a torch and bent it just a hare. It took about 5 miles to get used to and then I forgot about it until I read your last post.
SJ/JD
WildEd
Member
- 47
- 38
- 18
- Location
- Corbin,KY/Poynor,TX
Thanks for the info. That's definitely one of my options.
rustystud
Well-known member
- 9,280
- 2,987
- 113
- Location
- Woodinville, Washington
Good looking install. I used to install A/C units in vehicles when I was in Phoenix AZ.
WildEd
Member
- 47
- 38
- 18
- Location
- Corbin,KY/Poynor,TX
I notched the lower shifter bend, bent it X number of degrees, and re-welded it. It now clears. Dumb luck. Time to clean up the weld and paint it.
Last edited:
WildEd
Member
- 47
- 38
- 18
- Location
- Corbin,KY/Poynor,TX
The supplied brackets for the underdash unit are inadequate for anything beyond idling in the driveway. I fabricated an adjustable rear brace utlizing the heater blower upper mounts. The front differential engage switch has also been relocated. Down to wiring and hoses to the evaporator. 
r
r
WildEd
Member
- 47
- 38
- 18
- Location
- Corbin,KY/Poynor,TX
Leaky radiator hold-up
After dismantle and reinstall of radiator, a leak developed in the lower tank. Leak stop additives didn't work, so I removed it again and to the radiator shop it went. It should be ready tomorrow.
After dismantle and reinstall of radiator, a leak developed in the lower tank. Leak stop additives didn't work, so I removed it again and to the radiator shop it went. It should be ready tomorrow.
8madjack
Active member
- 416
- 78
- 28
- Location
- Gold country Ca.
Looks great, nice work. I need to put ac in my M931a1
rustystud
Well-known member
- 9,280
- 2,987
- 113
- Location
- Woodinville, Washington
That is a good installation job there WildEd ! I used to install complete A/C units in vehicles when I worked at a A/C shop Phoenix in the late 1970's . Back then most cars and trucks didn't come with factory A/C then.
V8srfun
Well-known member
- 423
- 538
- 93
- Location
- Altoona pa
Let us know how well it works the installation links nice