jwaller
Active member
- 3,724
- 19
- 38
- Location
- Columbia, SC
I gotta ask, whats with the warn decals?
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
All the stuff I did to my deuce, right here
- Thread starter sewerzuk
- Start date
sewerzuk
Member
- 524
- 12
- 18
- Location
- Seaside, OR
I was in a Warn commercial a few years ago on Spike TV; I just never removed the decals.
http://www.youtube.com/watch?v=F652JOD7OK4
smoothoperator
Member
- 63
- 1
- 8
- Location
- Royse City, TX
Sweet commercial spot!
TurboMustang370
Member
- 524
- 1
- 18
- Location
- Hamilton, NJ 08690
That's F'ing AWESOME!!
sewerzuk
Member
- 524
- 12
- 18
- Location
- Seaside, OR
2x4x.120 rectangle tube; used it for most of the frame, sides, cab guard, etc.
Thanks!! I'm about to build a flat bed for mine and the size you used looks perfect for the size of the truck.
sewerzuk
Member
- 524
- 12
- 18
- Location
- Seaside, OR
Just a quick update in the continuing ownership "saga" of my Deuce!
My annual trip to Mudfest in Sweet Home www.themud.com is coming up in a couple of weeks. This involves a few hundred miles on the highway and a day of driving in the mud; so I typically take this time to do a fairly complete preventative maintenance on my truck.
As part of that work, I pulled the hubs to inspect/repack wheel bearings. I noticed the front brake linings were showing some pretty significant wear (almost down to the rivets). So, it was brake time! I ordered a new set of shoes from a seller on ebay and installed them in the front axle. I also ordered 2 relining "kits" from Eastern Surplus for the rear axles. I haven't installed those yet, but when I do I'll be sure to post pics of the re-lining procedure (I haven't done this before, so I'll be learning along the way).
I also replaced the #3 injector line; it had a persistent leak at the injection pump end. I tried tightening it a little, but didn't want to really torque down on it and risk damaging the distribution head on the pump. The new line seems to have stopped the leak.
The original 6TL batteries were showing signs of failure (they were very old; not sure of the exact age, but they were at least 10 years old...possibly older). The truck was cranking over more slowly, and if I didn't leave the battery tenders plugged in both batteries would self-discharge over a few weeks. So, I purchased a dual optima tray from Ballistic Fabrication and installed a pair of Optima 34/78 yellow top batteries. I've had very good luck with the yellow tops; I have them in EVERY other vehicle that I own...one of them is 9 years old and still works like new. I typically subject the batteries to all manners of abuse, including welding, winching, repeated discharges, etc. The batteries in the deuce should lead a relatively easy life compared to my other rigs...
I put together my air fill/drain rig for the new valve stems on my MRAP wheels; it works great. Having those large bore valve stems is GREAT for quick air adjustment. I typically reduce air pressure in the tires when off road, and it usually takes close to 30 minutes to air them back up. Hopefully this will shave a few minutes off of that time.
My annual trip to Mudfest in Sweet Home www.themud.com is coming up in a couple of weeks. This involves a few hundred miles on the highway and a day of driving in the mud; so I typically take this time to do a fairly complete preventative maintenance on my truck.
As part of that work, I pulled the hubs to inspect/repack wheel bearings. I noticed the front brake linings were showing some pretty significant wear (almost down to the rivets). So, it was brake time! I ordered a new set of shoes from a seller on ebay and installed them in the front axle. I also ordered 2 relining "kits" from Eastern Surplus for the rear axles. I haven't installed those yet, but when I do I'll be sure to post pics of the re-lining procedure (I haven't done this before, so I'll be learning along the way).
I also replaced the #3 injector line; it had a persistent leak at the injection pump end. I tried tightening it a little, but didn't want to really torque down on it and risk damaging the distribution head on the pump. The new line seems to have stopped the leak.
The original 6TL batteries were showing signs of failure (they were very old; not sure of the exact age, but they were at least 10 years old...possibly older). The truck was cranking over more slowly, and if I didn't leave the battery tenders plugged in both batteries would self-discharge over a few weeks. So, I purchased a dual optima tray from Ballistic Fabrication and installed a pair of Optima 34/78 yellow top batteries. I've had very good luck with the yellow tops; I have them in EVERY other vehicle that I own...one of them is 9 years old and still works like new. I typically subject the batteries to all manners of abuse, including welding, winching, repeated discharges, etc. The batteries in the deuce should lead a relatively easy life compared to my other rigs...
I put together my air fill/drain rig for the new valve stems on my MRAP wheels; it works great. Having those large bore valve stems is GREAT for quick air adjustment. I typically reduce air pressure in the tires when off road, and it usually takes close to 30 minutes to air them back up. Hopefully this will shave a few minutes off of that time.
TurboMustang370
Member
- 524
- 1
- 18
- Location
- Hamilton, NJ 08690
Can you post a few photos of this? I'm interested since the CTIS on my 5-ton is not very reliable.
thanks.
sewerzuk
Member
- 524
- 12
- 18
- Location
- Seaside, OR
This is it! Pretty simple little setup. Cheap anodized aluminum air manifold with 4 ports, a 25' air hose cut in half, a 0-120PSI gauge, a small ball valve, and some fittings. The one shown in the pic has the large bore ag-style air chucks on it for the MRAP valve stems on my truck, but I have another very similar setup for standard valve stems.
sewerzuk
Member
- 524
- 12
- 18
- Location
- Seaside, OR
Seats!
So, I've been putting up with the stock Deuce seats in my truck since day 1. I have a long-ish trip coming up this weekend, and was not looking forward to sitting on the stock seats for 14 hours. Both seats were showing wear and tear, and have always been uncomfortable. Also, I've also never been a fan of lap belts...I've seen a number of significant internal injuries caused by a single lap belt. So, I decided to upgrade the seating! I purchased a couple of leather reclining bucket seats with slide rails and a couple of 4 point harnesses.
I had to build custom seat brackets specific to each side (the bolt holes are not in the same locations and do not have the same spacing on the driver and passenger side). I did add a couple of extra bolts through the floor, as I intend for the structure I built to ALSO carry the seat belt load.
The belts will not show up until tomorrow; I will post additional pics once everything is complete and installed in the truck.
So, I've been putting up with the stock Deuce seats in my truck since day 1. I have a long-ish trip coming up this weekend, and was not looking forward to sitting on the stock seats for 14 hours. Both seats were showing wear and tear, and have always been uncomfortable. Also, I've also never been a fan of lap belts...I've seen a number of significant internal injuries caused by a single lap belt. So, I decided to upgrade the seating! I purchased a couple of leather reclining bucket seats with slide rails and a couple of 4 point harnesses.
I had to build custom seat brackets specific to each side (the bolt holes are not in the same locations and do not have the same spacing on the driver and passenger side). I did add a couple of extra bolts through the floor, as I intend for the structure I built to ALSO carry the seat belt load.
The belts will not show up until tomorrow; I will post additional pics once everything is complete and installed in the truck.
srodocker
Well-known member
- 6,549
- 69
- 48
- Location
- Lacey, Washington
awesome! Cant wait to see mudfest pictures!
sewerzuk
Member
- 524
- 12
- 18
- Location
- Seaside, OR
Didn't get any good photos or video this year; my "normal" cameraman decided to back out of the trip because of work! And, there was just too much rain to get any good video footage...
My wife did snap some photos of me during the cleanup this morning. Once the underside of the truck stops dripping, I'll climb back under there with the grease gun...
On another note, a photographer for Petersen's 4x4 magazine was there and got a lot of "action" shots of the deuce...looks like I might end up on the pages of a magazine sometime in the coming months!
My wife did snap some photos of me during the cleanup this morning. Once the underside of the truck stops dripping, I'll climb back under there with the grease gun...
On another note, a photographer for Petersen's 4x4 magazine was there and got a lot of "action" shots of the deuce...looks like I might end up on the pages of a magazine sometime in the coming months!
Br0nc0xrapt0r
Member
- 70
- 2
- 6
- Location
- Kent City MI
About 6 years ago I decided I wanted a Deuce and started doing research. I came across your videos on youtube and I was really pleasantly surprized when I found your build thread on here. Thanks for documenting everything on here, I really love what you have done with it. My plans are to keep it very "Deuce" still but add lots of touches like you have, super single, gauges, Hydro steer. Bravo on the fantastic work and thanks for documenting it.
sewerzuk
Member
- 524
- 12
- 18
- Location
- Seaside, OR
Latest issue of Petersen's 4x4 magazine
I picked up the latest issue of Petersen's 4 wheel & off road, and there was my Deuce! Page 64...
I picked up the latest issue of Petersen's 4 wheel & off road, and there was my Deuce! Page 64...
peashooter
Well-known member
- 1,038
- 205
- 63
- Location
- Hanover, minnesota
That's pretty cool! Also how did your seat upgrade work out? What seats did you end up using and would you do anything different if you did it again? Any pictures of the new seats mounted? Thanks
rustystud
Well-known member
- 9,298
- 3,074
- 113
- Location
- Woodinville, Washington
Yes ! Pictures of the seats and where did you get the seats, who makes them ?
Thanks.
sewerzuk
Member
- 524
- 12
- 18
- Location
- Seaside, OR
Attached are some pics of the seats installed in the deuce (took them this morning). Hard to get a good angle inside of the cab! The're still a bit dirty from my last outing...
They worked out great; the side bolsters helped keep my butt firmly planted in front of the steering wheel, and the 4+ hour drive on the highway was significantly less painful. I should have done that upgrade years ago.
The seats are available at O'Reilly auto parts. They're fairly inexpensive...but they look good, and so far have held up well to abuse. And they're more comfortable than the factory seats.
