- 26,246
- 1,179
- 113
- Location
- NY
I've been running one for some time now. No issues, works great.
search "airtex" and or "E8131"
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Another fuel pump went bad
- Thread starter jerseyjeep2003
- Start date
I've been running one for some time now. No issues, works great.
search "airtex" and or "E8131"
JeffAS
New member
- 97
- 0
- 0
- Location
- Lessburg/Ohio
What fuels do you run with your Airtex fuel pump
Speedwoble
Well-known member
- 606
- 301
- 63
- Location
- New Holland, PA
The motor is completely sealed and actually drives the pump via a magnetic connection across an air-gap. If you have gunk in the bottom of your tank, the pump can seize and the motor sill continue to run. When you pull the unit out, try to move the pump by itself. You may only need to clean it and then clean your tank.
bjsmith
New member
- 272
- 1
- 0
- Location
- zachary,la
i just discoved my pump is bad so i will be installeing external aietex e8131 like i did on my last deuce
DieselBob
Active member
- 2,891
- 15
- 38
- Location
- Arnold Maryland
Also the magnetic coupling can fail. Thats what killed my pump. The magnet is glued into a cup on the bottom of the motor. The glue failed and allowed the magnet to dislodge from the cup which brought the hole show to a stop. If the pump you received was New OLD Stock it is possible that glue let loose from age. Problem is the only sure way to know is to open the motor housing.
Attachments
Motorcar
Member
- 271
- 3
- 18
- Location
- San Antonio, TX
Have you checked to see if you have an intermittent bad ground from that pump? A bit of rust where it grounds to the frame...wiggle the line changing it out and good for a couple of months then no go again...just tossing ideas out.
silverstate55
Unemployable
- 2,075
- 872
- 113
- Location
- UT
The fuel return line should take care of excess pressurized fuel by returning it to the fuel tank, shouldn't it?
bjsmith
New member
- 272
- 1
- 0
- Location
- zachary,la
Also others have used e8135 its 9 psi both are 35gph
jerseyjeep2003
New member
- 224
- 1
- 0
- Location
- Gloucester City NJ
I went to NAPA, and ordered the Airtex E8131. I picked it up and it is a Carter pump. It looks identical to the Airtex, so I am assuming that they both have the same internals and outputs, but, I could be wrong. I picked up the necessary compression fittings, and will be installing it tomorrow. I am going to use my original pump as the pick up in the tank. While I am in there I will check the tank for crude, but, it should be clean since it has only been a few months since I checked it. And hopefully Murray will do an exchange on the OE pump I got from him....still no word, and he hasn't returned my calls.
jerseyjeep2003
New member
- 224
- 1
- 0
- Location
- Gloucester City NJ
Where did you put your Airtex? The directions say to locate it as clow as possible. Does it make a difference? I am planning on using the existing copper line and compression fittings.
JeffAS
New member
- 97
- 0
- 0
- Location
- Lessburg/Ohio
I order a Airtex E8131 yesterday and picked it up today but when I got home and went to install it I was looking at the pump and it said 12 volts on it but it had the right part number on the other side to, I call them any order another one it will be in tomorrow after 1
JasonS
Well-known member
- 1,650
- 144
- 63
- Location
- Eastern SD
Why not just get the Parker pump mentioned on several threads now?
jerseyjeep2003
New member
- 224
- 1
- 0
- Location
- Gloucester City NJ
The airtex/carter was available locally, and I needed the truck up and running ASAP. I still may order the Parker as a backup.
Got it installed and it fired right up.