• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

Another wiring/ground issue with rear tail light

Indyharleyguy

Active member
Steel Soldiers Supporter
214
62
28
Location
Carmel IN
Hi All, My 1984 M1009 has a left rear tail light issue. At first the whole left tail light, brake light and turn signal light didn't work. I found the ground wire has rusted off. I fixed that and now have a brake light and turn signal. But the left tail light still didn't work. I thought ok even the bulb looked OK must be a bulb issue. My right tail light worked OK so I swapped them. Same problem, left tail light not working and right tail light working. I figure there must be another ground wire not working but not sure where to find it.
All other lights all the way around the truck work just fine.
Oh and the inside of the left tail light socket seems to be ok. At least I don't see any rust or corrosion anywhere in it.


Wanted to see if anyone had some thoughts.
Thanks
 

Barrman

Well-known member
5,255
1,766
113
Location
Giddings, Texas
Do you have a test light or volt meter? Since the tail light and brake light share an 1157 bulb housing. You can remove the bulb and check for voltage on the two leads at the bottom of the socket. If you have voltage there, then ground is still your issue. No voltage, then you get to do what the manual calls "chase wiring." Follow the wire to where the left/right split is on the driver side frame rail next to the fuel tank. Since the right side is working, the problem has to be between the split and the bulb housing.
 

Indyharleyguy

Active member
Steel Soldiers Supporter
214
62
28
Location
Carmel IN
Do you have a test light or volt meter? Since the tail light and brake light share an 1157 bulb housing. You can remove the bulb and check for voltage on the two leads at the bottom of the socket. If you have voltage there, then ground is still your issue. No voltage, then you get to do what the manual calls "chase wiring." Follow the wire to where the left/right split is on the driver side frame rail next to the fuel tank. Since the right side is working, the problem has to be between the split and the bulb housing.
Hi OK thanks. I'll test with my voltage meter and see what it tells me.
 

ezgn

Well-known member
650
1,039
93
Location
Lake Elsinore Ca.
Hi All, My 1984 M1009 has a left rear tail light issue. At first the whole left tail light, brake light and turn signal light didn't work. I found the ground wire has rusted off. I fixed that and now have a brake light and turn signal. But the left tail light still didn't work. I thought ok even the bulb looked OK must be a bulb issue. My right tail light worked OK so I swapped them. Same problem, left tail light not working and right tail light working. I figure there must be another ground wire not working but not sure where to find it.
All other lights all the way around the truck work just fine.
Oh and the inside of the left tail light socket seems to be ok. At least I don't see any rust or corrosion anywhere in it.


Wanted to see if anyone had some thoughts.
Thanks
https://www.steelsoldiers.com/threads/cucv-electrical-ground-locations.120289/
 

Mullaney

Well-known member
Steel Soldiers Supporter
Supporting Vendor
7,703
19,739
113
Location
Charlotte NC
Hi OK thanks. I'll test with my voltage meter and see what it tells me.
.
A little time spent under the dash (beside the E-Brake) is a ground in the thread that @ezgn referred you to. That ground in particular, a wire brush (small - tooth brush sized), and a tube of Anti-Oxidation Paste will make the entire truck happier. Read the link to find the others. Another option is a spray version of "AntiOx" that will help clean things up...
 

Indyharleyguy

Active member
Steel Soldiers Supporter
214
62
28
Location
Carmel IN
.
A little time spent under the dash (beside the E-Brake) is a ground in the thread that @ezgn referred you to. That ground in particular, a wire brush (small - tooth brush sized), and a tube of Anti-Oxidation Paste will make the entire truck happier. Read the link to find the others. Another option is a spray version of "AntiOx" that will help clean things up...
OK I'll check it out too. Thanks
 
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks