robson1015
Active member
- 515
- 132
- 43
- Location
- New Concord, Ohio
No cover yet but have been looking....
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Behr Paint Jobs- Show me your MV's
- Thread starter wsucougarx
- Start date
Another Ahab
Well-known member
- 17,996
- 4,549
- 113
- Location
- Alexandria, VA
Gemplers has 5-sided covers you might want to think about, and they'll even custom make you one to fit just right.
JoshHefnerX
New member
- 52
- 2
- 0
- Location
- Glendale, AZ
How big of a bottle of flotrol did you use with the paint whne you sprayed?
shepherm
New member
- 29
- 5
- 1
- Location
- Mustang, Oklahoma
I believe it was 32 oz.
That may be the size of the bottle, but there are specified amounts printed on it. One bottle will do many gallons. It's not 32oz to the gallon.
- 2,894
- 501
- 113
- Location
- Ft. Bragg, NC
Well, we are going to be attempting soon on the M880. Either tomorrow or next week/weekend. Trying to get her ready for the Veteran's Day Parade 7 NOV.
shepherm
New member
- 29
- 5
- 1
- Location
- Mustang, Oklahoma
You are correct there are instructions, and I followed them, up to 32 oz per gallon of paint with airless sprayers. My HVLP gun needs thinner paint than my airless sprayers, so I worked up to the max ratio. With the HVLP gun and high air temps I was spraying in this seemed to work good, but if you are painting with a brush or in cooler temps you may need a lot less.
They actually make a regulator "cage" that allows for legal transport with regulators on. Not to expensive and helps save the regulators from being beaten up.
That will allow for transportation of the bottles with those on but I still would stand them up. I have seen them break free when the valve stem broke off. They will do a lot of damage.
JoshHefnerX
New member
- 52
- 2
- 0
- Location
- Glendale, AZ
Well, I can say that here in phx @ 90 deg you need more than 4:1 flotrol. I mixed up at that ratio w/ a couple of oz's of water mixed in and the hf hvlp did kinda splatter. So the texture is pretty rough. However, I'm happy with it, covers up my crappy bodywork. lol
I will also say I had another learning experience. I decided to try rolling the roof after work one night. It was cooler (for phx) by the time I finished- maybe 70-75 and a bit humid as we'd had a couple of days of rain. The dew that popped up overnight managed to wash the paint off the top and down the sides all over the concrete.. I was kinda flabbergasted.
I will also say I had another learning experience. I decided to try rolling the roof after work one night. It was cooler (for phx) by the time I finished- maybe 70-75 and a bit humid as we'd had a couple of days of rain. The dew that popped up overnight managed to wash the paint off the top and down the sides all over the concrete.. I was kinda flabbergasted.
Kloakndagr
New member
- 266
- 4
- 0
- Location
- On The Road/California
I painted mine two years ago, Home Depot paint, Home Depot airless sprayer, I'm going to touch up some areas, for the most part the paint held up well. In fact I using the same paint to paint the 28 foot enclosed trailer it going to pull.
Last edited:
Kloakndagr
New member
- 266
- 4
- 0
- Location
- On The Road/California
I painted mine two years ago, Home Depot paint, Home Depot airless sprayer, I'm going to touch up some areas, for the most part the paint held up well. In fact I using the same paint to paint the 28 foot enclosed trailer it going to pull.
Attachments
Kloakndagr
New member
- 266
- 4
- 0
- Location
- On The Road/California
Don't know why it double posted....sorry
- 2,894
- 501
- 113
- Location
- Ft. Bragg, NC
Hey guys,
My buddy, the painter, is concerned about the durability of the Behr paint. It is showing some very easy scratch marks. I'm figuring it'll take a few days (longer when it's cold out) to fully dry and such... how off/on am I on this?
My buddy, the painter, is concerned about the durability of the Behr paint. It is showing some very easy scratch marks. I'm figuring it'll take a few days (longer when it's cold out) to fully dry and such... how off/on am I on this?
Attachments
- 3,871
- 497
- 83
- Location
- Gray Court SC
Bike mine is holding up well just got back from rally.
The only scratches are on the flat camo spots.
And the mud comes off easy on the behr.
By the way I used semi gloss because the flat does scratch and holds mud.
The only scratches are on the flat camo spots.
And the mud comes off easy on the behr.
By the way I used semi gloss because the flat does scratch and holds mud.
grayparatrooper
Member
- 121
- 0
- 16
- Location
- Dallas tx
How did you paint behind the cab?
- 3,871
- 497
- 83
- Location
- Gray Court SC
Pull the spare out of the rack and spray.
Used Behr Ultra Premium on my 817 dump truck with floetrol. It takes from a week to a month to fully cure. Reminds me of the cure rate for concrete. After 111 loads, it needed a touch-up. Red oxide primer on rust is a must.
Cape Coastie
CWO4 ENG/MSS, USCG, RET.
- 528
- 124
- 43
- Location
- Sandwich, MA
Hey Gray, as Coffey1 says pull the spare and paint. I just haven't pulled mine yet as I need to modify my rack to fit the larger tire.
Rmtaunton
Well-known member
- 1,510
- 31
- 48
- Location
- Smyrna, ga
That and it really does take about a month to harden
Doc2012
New member
- 10
- 1
- 3
- Location
- Jacksonville, NC
So, I want to get this straight.
All I have to do is go to HD, tell them to look up competors paint, have them use the federal standard paint code, and mix it, correct?
SO, if I wanted to go with a Medium Gunship Grey, I would tell them to use the Federal Standard Code 36118, correct?
Got that code from federalstandardcolor.com, for those that willing to help out.
All I have to do is go to HD, tell them to look up competors paint, have them use the federal standard paint code, and mix it, correct?
SO, if I wanted to go with a Medium Gunship Grey, I would tell them to use the Federal Standard Code 36118, correct?
Got that code from federalstandardcolor.com, for those that willing to help out.