- 4,318
- 3,208
- 113
- Location
- Fort Worth, Texas
I'm outside without cover. I watch the weather meticulously and paint mid-mornings.
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Behr Paint Jobs- Show me your MV's
- Thread starter wsucougarx
- Start date
Waterhouse
Active member
- 158
- 161
- 43
- Location
- Marianna, fl
Well, I just painted another test piece. I did the best job in prep. Scotch-brite and wipe down with brake clean. The primed with zinc cromate. This one I painted full strength in the shade. It seems like if the metal is hot, it's not as smooth. It still has some texture. I'm going to let it alone for a couple weeks and do some scratch tests. I'm assuming after a full cure, you can use a pressure washer on this paint?
RustyEric
New member
- 16
- 13
- 3
- Location
- Cape cod Massachusetts
I know this is an old thread but do you remember how you got that color? do you still have the mix code?
SCSG-G4
PSVB 3003
- 5,379
- 3,413
- 113
- Location
- Lexington, South Carolina
FSS 24084 is the semi gloss version, if it were flat it would be 34084. Tell the people at Home Depot to look up "Competitive paints", scroll down to find "FSS" (Federal Supply Service), select it, then in the number part have them enter '24084' and press enter. Then tell them how many gallons you want.
- 3,871
- 497
- 83
- Location
- Gray Court SC
Go with semi gloss if you want to be able to clean truck easily. It's shiny at first but will dull down.
RustyEric
New member
- 16
- 13
- 3
- Location
- Cape cod Massachusetts
Do you remember what size tip you used in the graco sprayer?
RustyEric
New member
- 16
- 13
- 3
- Location
- Cape cod Massachusetts
Thank you. My understanding is the new 24084 is the same as the vietnam era 24087
3rdmdqm
Active member
- 446
- 136
- 43
- Location
- Woodbine Maryland
I'm in the middle of full frame off restoration of a '68 Deuce. While disassembling, I found some of the original era paint under a removed part which appeared in pristine color condition, unexposed to elements or light. This was taken to Home Depot last month and an exact (and I mean exact) color match to the original paint was produced using their color match system instead of going to the competitor color system lists. The attached mix is what I obtained, it is Behr Marquee semi-gloss. I'm very happy with the result. It looks identical to the picture of the dashboard by Privatewrench quoted by RustyEric in the post above. Hope this helps.
Attachments
RustyEric
New member
- 16
- 13
- 3
- Location
- Cape cod Massachusetts
Thats great thank you.
Privatewrench
Member
- 127
- 19
- 18
- Location
- Kentucky
Sorry RustyEric... been away for a little while. I did axactly what SCSG-G4 stated to do at home Depot. This is the sticker on top of the can with the color code they mixed. I had him print an extra sticker so I can have more paint mixed without bringing in the can.
Attachments
RustyEric
New member
- 16
- 13
- 3
- Location
- Cape cod Massachusetts
Thanks. Thats great. Do you have any pics of how the rest of the truck came out?
Privatewrench
Member
- 127
- 19
- 18
- Location
- Kentucky
Sure do. This pic is right before I stencilled the hood.
Attachments
RustyEric
New member
- 16
- 13
- 3
- Location
- Cape cod Massachusetts
looks awesome. just the color i want. what did you paint the stack with?
Privatewrench
Member
- 127
- 19
- 18
- Location
- Kentucky
I just used black high temp grill paint. I added the Behr paint to the bottom of stack to test it, and have had not problem with heat effecting it. I might cover the whole stack now with the same paint I used on the truck
Sent from my SM-G973U using Tapatalk
Sent from my SM-G973U using Tapatalk
Terra1936
Active member
- 201
- 124
- 43
- Location
- El Cajon/California
How has the latex held up on the bed? Inside? Does it scratch of easy?
Terra1936
Active member
- 201
- 124
- 43
- Location
- El Cajon/California
Did you paint the inside of bed? If so, how does it hold up?
SCSG-G4
PSVB 3003
- 5,379
- 3,413
- 113
- Location
- Lexington, South Carolina
I have painted the inside of my bed with the BEHR paint. It will scrape off when the cargo is dirty, or gritty and drug over the bed. But, I have a coat of Rustoleum Rusty Red Primer underneath that and so far it has not had any more rust. If you were to take a picture of the bed from 20 feet up, it would still look 80 percent green. YMMV.
Privatewrench
Member
- 127
- 19
- 18
- Location
- Kentucky
I haven't painted the bed yet. I use it frequently to haul and thought I should hold off until I finish some projects around the house. I plan to paint on a bedliner, then cover that with Behr. I did that on floors in the cab, and it came out great.
Jeep Nasty
Active member
- 379
- 244
- 43
- Location
- NH
Another Behr paint job in the books for me. I think this makes 9 or 10.
I didn’t use official colors, this time, I just picked a couple I liked that popped.
I went semi gloss
I barely prep, pressure wash, tape, spray. I’m a sloppy painter and hate doing it. I oversprayed the crap out I’m my tires but I don’t care. I had to finish up to take my daughter to a sleepover.
To me about 8 hours and that because it was below freezing last night and I had to thaw my hose before pressure washing.
Sent from my iPhone using Tapatalk
I didn’t use official colors, this time, I just picked a couple I liked that popped.
I went semi gloss
I barely prep, pressure wash, tape, spray. I’m a sloppy painter and hate doing it. I oversprayed the crap out I’m my tires but I don’t care. I had to finish up to take my daughter to a sleepover.
To me about 8 hours and that because it was below freezing last night and I had to thaw my hose before pressure washing.
Sent from my iPhone using Tapatalk
Another Ahab
Well-known member
- 18,007
- 4,579
- 113
- Location
- Alexandria, VA
The semi-gloss looks great!I went semi gloss