trooper632
Member
- 533
- 3
- 18
- Location
- Utopia, TX
I hope this is the right forum for this, How much to transport a M936 wrecker from camp shelby MS to San Antonio TX, it runs,
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Camp Shelby M936 to San Antonio TX
- Thread starter trooper632
- Start date
M1075
Active member
- 3,589
- 6
- 38
- Location
- Oklahoma City
I would budget $3-$4 per mile.
wreckerman893
Possum Connoisseur
- 15,629
- 2,054
- 113
- Location
- Akenback acres near Gadsden, AL
Mapquest says 631 miles.....at 3.00 per mile you are looking at $1893.00 or there a bouts.
Not being a smarta$$ but did you check on shipping before you bid?
tbci
New member
- 15
- 0
- 0
- Location
- Alexandria, LA
I can recover and haul it for you. Would haul it with triaxle stepdeck. Would have enough room left to haul a CUCV or smaller size. Loaded mile rate of $4.00
Semi-truck with a 53' tri-axle step deck or a 60 ton lowboy for larger loads. Truck is 24V which helps with recoveries.
One ton P/U with 40' triple-tandem or 35' dual-tandem gooseneck for smaller loads. 35' trailer is set up with a hydraulic folding dove-tail and winch for recovery of non-running vehicles. I generally bring a set of hot batteries with me when recovering with my one-ton.
As a general rule of thumb; I always bring a couple gallons of engine oil, 5 gallons of water, 5 gallons of hydraulic oil, and a set of hand tools with me whenever I'm picking up a truck from GL.
Fully licensed & Insured. Apportioned for LA, TX, AR, OK, & MS but can permit nationwide.
$4.00/loaded mile for Semi-truck loads. Can haul up to 3 vehicles per load.
$2.75/loaded mile for Gooseneck loads. Can haul up to 2 vehicles per load.
Rates include my time for recovery. Any customer approved expenses in parts or materials will require re-imbursement upon delivery.
I currently have about 10 loads of our own equipment that I will be hauling from Joplin, MO to Alexandria, LA over the next month. Can pull loads going north on or near that route for $2.00/loaded mile-Semi-Truck, $1.25/loaded mile Gooseneck.
Michael Seeling
Twin Bridges Company, Inc.
318.792.2039 Cell
318.445.1692 Office
Attached Thumbnails
Semi-truck with a 53' tri-axle step deck or a 60 ton lowboy for larger loads. Truck is 24V which helps with recoveries.
One ton P/U with 40' triple-tandem or 35' dual-tandem gooseneck for smaller loads. 35' trailer is set up with a hydraulic folding dove-tail and winch for recovery of non-running vehicles. I generally bring a set of hot batteries with me when recovering with my one-ton.
As a general rule of thumb; I always bring a couple gallons of engine oil, 5 gallons of water, 5 gallons of hydraulic oil, and a set of hand tools with me whenever I'm picking up a truck from GL.
Fully licensed & Insured. Apportioned for LA, TX, AR, OK, & MS but can permit nationwide.
$4.00/loaded mile for Semi-truck loads. Can haul up to 3 vehicles per load.
$2.75/loaded mile for Gooseneck loads. Can haul up to 2 vehicles per load.
Rates include my time for recovery. Any customer approved expenses in parts or materials will require re-imbursement upon delivery.
I currently have about 10 loads of our own equipment that I will be hauling from Joplin, MO to Alexandria, LA over the next month. Can pull loads going north on or near that route for $2.00/loaded mile-Semi-Truck, $1.25/loaded mile Gooseneck.
Michael Seeling
Twin Bridges Company, Inc.
318.792.2039 Cell
318.445.1692 Office
Attached Thumbnails
- 10,466
- 6,540
- 113
- Location
- Camp Wood/LC, TX
I paid $1.50 a mile to get my 22,000lb M931 from Shelby to Houston. 500 miles. $1.50 is as good a rate as you will find.
M1075
Active member
- 3,589
- 6
- 38
- Location
- Oklahoma City
$1.50 is a great rate, especially if was a dedicated load.
trooper632
Member
- 533
- 3
- 18
- Location
- Utopia, TX
NDT, well who hauled it for you