JZAM75
New member
- 9
- 2
- 3
- Location
- DePere, Wisconsin
THE GLOW PLUG SYSTEM WILL NOT WORK, SMART BOX WAS BURNT UP. REPLACED BOX, GLOW PLUGS AND CONTROLLER, STILL NO OPERATION. ANY HELP WOULD BE GREATLY APPRECIATED.
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
CRANK NO START
- Thread starter JZAM75
- Start date
- 2,958
- 4,311
- 113
- Location
- Olympia/WA
A couple things to start off with:
1) has this vehicle ever started for you, or did you receive it in this condition?
2) Using a multimeter, do you show voltage at the glow plugs when they are cycling?
3) Do you have any smoke out the exhaust while cranking the engine?
4) Caps lock is generally considered to be shouting, and we can read just fine without it.
5) What model/serial number truck are we talking about? The systems are generally the same, but there can be small differences that make a lot of difference when trying to troubleshoot issues.
1) has this vehicle ever started for you, or did you receive it in this condition?
2) Using a multimeter, do you show voltage at the glow plugs when they are cycling?
3) Do you have any smoke out the exhaust while cranking the engine?
4) Caps lock is generally considered to be shouting, and we can read just fine without it.
5) What model/serial number truck are we talking about? The systems are generally the same, but there can be small differences that make a lot of difference when trying to troubleshoot issues.
- 3,569
- 3,474
- 113
- Location
- Brooklyn, NY
Respectfully, all caps posts are a no-go.
Profiles require city and state IIRC. Please fix your profile.
What year and what model?
Did you replace the fuel and ensure the water is removed from the filter?
Is your injection pump functional?
Is white smoke exiting your exhaust?
Is the ambient temperature above or under 55?
Are glowplugs checked with multimeter to establish they are working?
Are batteries fresh and fully charged and are connections clean and tight?
Profiles require city and state IIRC. Please fix your profile.
What year and what model?
Did you replace the fuel and ensure the water is removed from the filter?
Is your injection pump functional?
Is white smoke exiting your exhaust?
Is the ambient temperature above or under 55?
Are glowplugs checked with multimeter to establish they are working?
Are batteries fresh and fully charged and are connections clean and tight?
Last edited:
JZAM75
New member
- 9
- 2
- 3
- Location
- DePere, Wisconsin
It's a m1097r1 and I think the ser# is 511670. It has fresh fuel, filters and a new lift pump on it. I have had it running but only with ether. Runs good after its started but i dont like using ether. There is no voltage out to plugs when ignition is first turned on, the wait to start light flashes on for a split second then nothing.
- 3,569
- 3,474
- 113
- Location
- Brooklyn, NY
Never use ether….ever.
You’re lucky if your heads are not cracked
You’re lucky if your heads are not cracked
- 3,569
- 3,474
- 113
- Location
- Brooklyn, NY
You need to measure resistance across the plugs to see if they are functional
- 6,871
- 9,512
- 113
- Location
- Papalote, TX
X2 on never use ether.
Did you change the TSU, and make sure it matches the EESS box?
EDIT, I see you say you replaced the "controller" I assume you meant the TSU
What part number is on your EESS box and was it new?
JZAM75
New member
- 9
- 2
- 3
- Location
- DePere, Wisconsin
JZAM75
New member
- 9
- 2
- 3
- Location
- DePere, Wisconsin
This is what was purchased from midwest Military Supply. The part # of the 1 that was in it was a cr-2695. The description said it was a new/unused part. It bolted in without an issue and both connections were the same.
- 6,871
- 9,512
- 113
- Location
- Papalote, TX
That does not look like a "real" box, I could be wrong but it looks like an aftermarket box, one never wants to buy an aftermarket part for the Humvee, especially an electronic part.
Did the glow plugs take 10MM or 3/8" wrench?
JZAM75
New member
- 9
- 2
- 3
- Location
- DePere, Wisconsin
The glow plugs were 3/8. Both the ones I took out and the new ones that went back in. The box came with the tsu to match it.
JZAM75
New member
- 9
- 2
- 3
- Location
- DePere, Wisconsin
Hopefully we didn't waste $1000 on something that wont work for this. Can you tell me where the best place to get parts is for these.?
You need to put some effort in here for us to help you. You were asked if you ohmed the GP. No response. We here on the internet can't magically fix your problem. Search these forums, read old posts and learn. These are very simple trucks. With your WAIT light flashing briefly, me thinks you smoked your box. Get your DVM out and start doing some testing.
BLK HMMWV
Well-known member
- 1,574
- 491
- 83
- Location
- Pasadena California
Did you disconnect the batteries before you changed out the box?
- 6,066
- 4,417
- 113
Brief blip on the wait light and then nothing could also be weak batteries with low voltage. I've seen that more than once. Even if they crank the truck ok.
JZAM75
New member
- 9
- 2
- 3
- Location
- DePere, Wisconsin
I have ohmed out the glow plugs, they are less than 2 ohms. They are new plugs that were put in along with the smart box. Batteries were disconnected when box was replaced. I haven't charged the batteries , but I did load test them and both passed.
- 2,958
- 4,311
- 113
- Location
- Olympia/WA
Next step is see what voltage you have at the glow plugs.
- 4,390
- 4,170
- 113
- Location
- Brentwood, Calif
This box is made in Turkey I do believe, it is not an OEM Nartron or KDS…
JZAM75
New member
- 9
- 2
- 3
- Location
- DePere, Wisconsin
No voltage out to plugs
- 3,569
- 3,474
- 113
- Location
- Brooklyn, NY
I’ve helped a few members with similar issues. Simple affordable DIY solution.
How to bypass PCB? I am aware some HMMWV owners have done it. TOBASH
I'm not trying to speak sacrilege here, and I don't want to precipitate a war of words. :shock: How might I build a manual control box? My 24Volt Landcruiser just uses a glow wire to show glow plugs are ready, and then she just starts right up with the twist of a key. Civilian 6.2 Diesel...
www.steelsoldiers.com