Decimal drill size chart.

[SCSG-G4]

From a gull wing trailer being scrapped, here is a decimal to drill size chart from .0135 to one inch

 

[gringeltaube]

Being a picture, it's blurry and hard to read, even blown-up to 300%.

Maybe that same chart does exist somewhere in PDF-format? What about that trailer's corresponding TM?

 

[Guyfang]

Mike, I thought you have that TM?

 

[SCSG-G4]

Mike, I thought you have that TM?

I probably do. but this one was USMC and did not have the Army TM number with the gull wing.

 

[SCSG-G4]

Being a picture, it's blurry and hard to read, even blown-up to 300%.

Maybe that same chart does exist somewhere in PDF-format? What about that trailer's corresponding TM?

The original scan is 3MB, when uploading it to the site, it dropped to 600K, that's why it's fuzzy! The upload process got rid of five of every six pixels. I may try uploading it again as a horizontal image to see if it is any better.

 

[SCSG-G4]

Uploading again, this time horizontal.

 

[gringeltaube]

OK, much better, Mike.

Still, I would like to see that original, for comparison (and possibly convert to PDF). Can you please email it to me?

 

[SCSG-G4]

It's a metal plate, with sharp edges, not easy to mail. it measures 9 3/8 inches (23.9 cm) tall, and 5 3/4 inches (14.6 cm) wide. Send me your e-mail address and I will send you the full sized scan.

 

[INFChief]

Being a picture, it's blurry and hard to read, even blown-up to 300%.

Maybe that same chart does exist somewhere in PDF-format? What about that trailer's corresponding TM?

I’m sure there’s a part # for it.

 

[gringeltaube]

It's a metal plate, with sharp edges, not easy to mail. it measures 9 3/8 inches (23.9 cm) tall, and 5 3/4 inches (14.6 cm) wide. Send me your e-mail address and I will send you the full sized scan.

Lol... I sure meant the full size picture, not the plate itself... gringeltaube@gmail.com

 

[SCSG-G4]

OK, much better, Mike.

Still, I would like to see that original, for comparison (and possibly convert to PDF). Can you please email it to me?

The original scan is 1412 pixels by 889 pixels, and saved as a PNG file is 3.0 MB in size, and 3.3 Mb as a TIFF, JPG and BMP files are much smaller.

 

[SCSG-G4]

Lol... I sure meant the full size picture, not the plate itself... gringeltaube@gmail.com

on the way momentarily.

 

[gringeltaube]

on the way momentarily.

Got it, thanks!

Is this your personal, secret "watermark"? Should it appear/remain in the PDF, also.....?

 

[SCSG-G4]

Got it, thanks!

Is this your personal, secret "watermark"? Should it appear/remain in the PDF, also.....?

View attachment 865424

It was some dirt rubbed onto the plate when the South Bend Lathe came out. I had washed most of it off but some was stubborn. The three phase motor on that lathe weighs more than I do, by a good margin. I try washing it again and rescan.

 

[gringeltaube]

I try washing it again and rescan.

Please no, it's not necessary; don't waste your time! I was just joking about that fingerprint; it is very easy for me to make it disappear.
Will post the PDF file, later tonight.



Edit: Attached PDF....

 

[Guyfang]

G,

You sound like a hacker!! Or a counterfeiter?

 

[gringeltaube]

You sound like a hacker!! Or a counterfeiter?

Oops... really....?? Naw, it's not my speciality. I'd better leave that for the professionals....

All it took is a bit of photoshopping, to remove some stains.