Elk1111
Well-known member
- 282
- 490
- 63
- Location
- Las Cruces NM
I have a friend stuck in Pecos Texas with a hard brake pedal and the rear brakes smoking. Any ideas how to do a roadside repair to get him rolling again.
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Deuce Brakes
- Thread starter Elk1111
- Start date
- 682
- 378
- 63
- Location
- Ozona Texas
Maybe open service side of air just a hair, to let vent.
Sent from my moto z3 using Tapatalk
Sent from my moto z3 using Tapatalk
- 6,426
- 4,985
- 113
- Location
- Ft. Lauderdale, Florida
Take the hotttest drum and disconnect the hydraulic line and plug it.
Attachments
- 682
- 378
- 63
- Location
- Ozona Texas
I had someone put tacks or small nails to seal off one of mine before. Head was perfect size to seal the line. Wondered why brakes wouldn't work.
Sent from my moto z3 using Tapatalk
Elk1111
Well-known member
- 282
- 490
- 63
- Location
- Las Cruces NM
I had him back off the brake shoes a bit and let it cool down. Pedal is back to normal. He’s rolling again and will stop every 25-50 miles to reassess. He’s got 225 miles to go.
Does anyone know how much a bobbed deuce weighs in case we have to trailer it?
Does anyone know how much a bobbed deuce weighs in case we have to trailer it?
tguinn
Active member
- 45
- 114
- 33
- Location
- savannah,MO
approx 10,500, thats what mine weighs
Elk1111
Well-known member
- 282
- 490
- 63
- Location
- Las Cruces NM
Thank you. He’s almost home with no more problems. We’ll flush everything out and inspect everything when he gets here.
- 3,265
- 3,395
- 113
- Location
- NORTH (Canada)
Bleed hole in master cylinder (small hole to the rear, at the bottom) clogged or sticky airpack! My 5 cents.
- 6,426
- 4,985
- 113
- Location
- Ft. Lauderdale, Florida
I knew I seen that before
Get the proper fittings and wrenches and kroil
That was my How to get home post.
Get the proper fittings and wrenches and kroil
That was my How to get home post.
Attachments
- 333
- 262
- 63
- Location
- Denver, Colorado
And, IIRC, if the Master Cylinder rod doesn't have enough free play travel, then it can't vent the pressure when the brakes are released, through that little hole, back into the reservoir.
dmetalmiki
Well-known member
- 5,523
- 2,029
- 113
- Location
- London England
Bleed out some of the brake fluid, then follow the advice's posted by others.
- 34,012
- 1,810
- 113
- Location
- GA Mountains
That little hole is called a compensating port if anyone really needs to know.
- 4,811
- 746
- 113
- Location
- Liberty Hill, SC
This is exactly what happened with my m818, I had replaced the MC and the rod was just a tad too long... kept having to stop and open a bleed screw. Thought I got trash in the MC or air pack. Adjusted rod and was smooth sailing.
A bobbed deuce. Unless an A3, it has 1 3/8" cups in the wheel cylinders. The A3 uses a 1 1/2" cylinder on the front and has1 3/8" on the back.
Thing is, the 11/2" wheel cylinders will fit with a small rod length modification on both front and back on the deuce and since the back axle is removed, even the stock system single circuit, can deliver about 20% more force. The volume of fluid on 6 wheels with 1 3/8" is about equal to 4 wheels with 1 1/2"
With everyone going to even bigger singles than the 14.5 on the A3, there is a need for more braking force so please consider using the 1 1/2 like the A3 front allthe way around your bob deuce
Thing is, the 11/2" wheel cylinders will fit with a small rod length modification on both front and back on the deuce and since the back axle is removed, even the stock system single circuit, can deliver about 20% more force. The volume of fluid on 6 wheels with 1 3/8" is about equal to 4 wheels with 1 1/2"
With everyone going to even bigger singles than the 14.5 on the A3, there is a need for more braking force so please consider using the 1 1/2 like the A3 front allthe way around your bob deuce
- 6,426
- 4,985
- 113
- Location
- Ft. Lauderdale, Florida
One way or another Me thinks they been home long time now.