Another Ahab
Well-known member
- 18,007
- 4,579
- 113
- Location
- Alexandria, VA
What is "wms"?
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Dually conversion done simple on the cheap.
- Thread starter corelokt
- Start date
KsM715
Well-known member
- 5,149
- 142
- 63
- Location
- St George Ks
Wheel mounting surface.
- 34,012
- 1,810
- 113
- Location
- GA Mountains
It has GM shock mounts but they have been reinstalled upside-down.
corelokt
Member
- 859
- 2
- 16
- Location
- Duffield, VA. (East of nowhere).
I found a winner!
Chicken fricken dinner!
CUCV take out!
Chicken fricken dinner!
CUCV take out!
corelokt
Member
- 859
- 2
- 16
- Location
- Duffield, VA. (East of nowhere).
Before I take off on an odyssey...
What are the odds it's not 4.56 or not a detroit locker?
What are the odds it's not 4.56 or not a detroit locker?
rustystud
Well-known member
- 9,298
- 3,074
- 113
- Location
- Woodinville, Washington
At this point does it matter ? If you can buy it cheap enough gears can be easily changed, and lockers added if you think you really need them.
86m1028
Active member
- 1,687
- 17
- 38
- Location
- Murphy TEXAS
If the truck had a 350 or 6.2 in it there is a possibility of 4.56's
Detroit on the other hand is unlikely unless it was a military axle.
corelokt
Member
- 859
- 2
- 16
- Location
- Duffield, VA. (East of nowhere).
It was a cucv, per owner. I asked them to spinning a hub and see what the other one does and if it feels like their connected to each other. I'm definitely buying if it's locked. Otherwise I'll go narrow 14 bolt.
Is there any chance of my 14 bolt, larger, ujoint yoke I bought fitting it?
Or, am I lucky enough the ujoint is already 1410?
Is there any chance of my 14 bolt, larger, ujoint yoke I bought fitting it?
Or, am I lucky enough the ujoint is already 1410?
Last edited:
corelokt
Member
- 859
- 2
- 16
- Location
- Duffield, VA. (East of nowhere).
What's an open diff D70 worth? I can't afford to take a loss right now.
- 3,348
- 1,340
- 113
- Location
- The actual midwest, NM.
I'd start by pulling the diff cover, and brake drums, to find out what needs it may have. A rusted ring gear and/or pinion would cost a few bucks to replace, for example.
Unless you're changing the ratio and installing a locking diff, anyway.
Oh, and properly functioning Detroit would likely act like an oped diff if you turn one side, except with a slight "clicking" sound.
If you rotated the pinion and both ends turned the same way it's most likely not an open diff.
Unless you're changing the ratio and installing a locking diff, anyway.
Oh, and properly functioning Detroit would likely act like an oped diff if you turn one side, except with a slight "clicking" sound.
If you rotated the pinion and both ends turned the same way it's most likely not an open diff.
Last edited:
corelokt
Member
- 859
- 2
- 16
- Location
- Duffield, VA. (East of nowhere).
Just a tad overkill, or go for it?
Last edited by a moderator:
corelokt
Member
- 859
- 2
- 16
- Location
- Duffield, VA. (East of nowhere).
It's always been this way too. Used to be we would write $50.00 on the bill of sale. Then they made a minimum value to prevent that. Back when I was a kid, you could buy a running Chrysler Cordoba ETS for $50 bucks. A-holes is right.
You cannot even give away a car to your own brother without paying taxes on it ! I gave my brother our old 1999 Honda Civic since his old car has over 470,000 miles on it ! That's right almost half a million miles ! The old thing is barely holding together though, so they desperately needed a new car but could not afford one. At the license transfer place they wanted the value of the car for tax purposes ! If you think about it the average car gets sold three times. That's three times it's taxed ! I've always been glad that we are on a well so we don't pay the water bill and tax. Now some A$$ Wipe in the legislature is trying to pass a "Well Water Tax" !!!! Our fore-fathers would roll-over in their graves if they only knew what we are putting up with in all these taxes we pay. They started a revolution for having to pay only 4% of their income !
I'm sorry for getting on this rant, but taxes are a real sore spot for me. Especially land tax. If you think about it we never really own our land but just "rent" it from the government ! Don't think so ? Then just don't pay your rent (taxes) and see what happens !
- 34,012
- 1,810
- 113
- Location
- GA Mountains
For what its worth, the cost of a Detroit NoSpin for a 70HD is nearly twice the cost of one for the 14B.
86m1028
Active member
- 1,687
- 17
- 38
- Location
- Murphy TEXAS
I know the detroits for the 14 bolts have gone up but OUCH on the Dana 70 detroit prices !!!
corelokt
Member
- 859
- 2
- 16
- Location
- Duffield, VA. (East of nowhere).
I'm hoping it's in there as it was a cucv axle.
corelokt
Member
- 859
- 2
- 16
- Location
- Duffield, VA. (East of nowhere).
Hartford, Conn.
corelokt
Member
- 859
- 2
- 16
- Location
- Duffield, VA. (East of nowhere).
Is a D80 overkill?
- 3,348
- 1,340
- 113
- Location
- The actual midwest, NM.
On a Suzuki Samurai, yes. For a vehicle that has lots of torque and can carry heavy loads, probably not.
But with everything being bigger, so are the price tags for parts. And then there's the extra weight, which comes out of your total load carrying ability.
rustystud
Well-known member
- 9,298
- 3,074
- 113
- Location
- Woodinville, Washington
If I could find one for a reasonable price I would buy it. The major difference between the Dana 80 and the Dana 70HD is the Dana 80 uses disc brakes and the Dana 70HD uses drums. They are the same weight and strength. Some get confused when comparing the 70 to the 80 but they forget the "Dana 70HD" is built heavier then the stock Dana 70. It has a 4" tube instead of 3.5" and it uses much heavier carrier bearings. Basically the Dana 80 is just a modern Dana 70HD since all trucks and cars use disc brakes all around now. The question then becomes is it worth the extra cost of the Dana 80 for the disc brakes ?