robson1015
Active member
- 515
- 132
- 43
- Location
- New Concord, Ohio
Guyfang - I have an assortment pack of o-rings but don't know if they are diesel fuel compatable.
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Finally joined the MEP-803A club...
- Thread starter robson1015
- Start date
- 16,703
- 23,937
- 113
- Location
- Burgkunstadt, Germany
Diesel is not so aggressive on O-rings. The JP-8 we used in the military was a different deal.
If it works, don't screw with it. Wait until you need to change the filter.
Interesting. I went to the Lister Petter parts book. They have wonderful pictures of the filter assembly. But no breakdown of it.
Some of the guys who have had sets a long time need to chime in here.
If it works, don't screw with it. Wait until you need to change the filter.
Interesting. I went to the Lister Petter parts book. They have wonderful pictures of the filter assembly. But no breakdown of it.
Some of the guys who have had sets a long time need to chime in here.
- 3,816
- 5,894
- 113
- Location
- MA
I am in the midst of building a load bank that will go up to 13.5kw for this very reason.. the 803A currently under my watch has the thermostat pegged at 180 and unmoving (but it did move when I first got the machine). My hookup on my house is only 30A, so I cant even draw enough to make this thing sweat. I am adopting most of this design, with some changes to work for me: https://www.steelsoldiers.com/showthread.php?163190-Homemade-Load-Bank
When I am done building it, I will share with the forum.
robson1015
Active member
- 515
- 132
- 43
- Location
- New Concord, Ohio
Don't know if you can see it in the pic but the frequency control knob-button is missing. The spring is broken. I'm still able to adjust it by twisting but it's not functioning correctly. Ordered a new one from Armyproperty.com NSN 2990-01-385-9030. No picture of this part anywhere. Cross reference from the parts manual shows this NSN # so I have my fingers crossed that it's the right cable assembly. $51.00 free shipping. I'll let everyone know when it shows up here. Thanks to 'Light in the dark and' and 'Guyfang' for the info. on this.
This was the sticker on the control panel door when I picked it up.
Last edited:
robson1015
Active member
- 515
- 132
- 43
- Location
- New Concord, Ohio
Update - just got an e-mail from Armyproperty.com, they gave me a full refund and stated that they can't fulfill the order - ???
Last edited:
- 3,816
- 5,894
- 113
- Location
- MA
Lovely, even though their website says available for sale. I have sent an email off to an associate of mine to see if they can source. Will advise.
- 3,816
- 5,894
- 113
- Location
- MA
If you are bored, the manufacturer of the part (According to the NSN is B.W. ELLIOTT MANUFACTURING CO., LLC). The manufacturer part number is 347L-032-2. I show BW has a dealer in Ohio... wouldn't hurt to call them to see if they can source it for you?
Ohio Pipe Valves & Fittings4000 Trent AvenueCleveland OH 44109
Phone: 216-631-6200Email: mresch@valvepros.com
Zed254
Well-known member
- 866
- 466
- 63
- Location
- S. Hampton Roads, VA
This may be an option: https://www.amazon.com/Buyers-Produ...r=8-2-fkmr1&keywords=throttle+control+vernier
The Buyers Products one says it is a vernier cable but their web site is pretty weak on details. The Dorman must not have any fine adjustment per comments from one buyer.
The Buyers Products one says it is a vernier cable but their web site is pretty weak on details. The Dorman must not have any fine adjustment per comments from one buyer.
robson1015
Active member
- 515
- 132
- 43
- Location
- New Concord, Ohio
I am trying to find original part due to the amazon cable is larger diameter and won't fit into the nuts that hold the cable. Also there is a fixed cable end on the original that fits the throttle plate. May have to try the amazon one if I strike out. 
The water temp gauge started working after I shut the unit down with the emergency stop button and restarted it. Go figure. All gauges work and it runs good without load. I'm curious to see what the governor does under load. Searching for load bank next.
Put a fancy exhaust flapper on but it was too noisy, went back to the original cover flapper.
Got all the openings covered with hardware cloth except the large opening under the engine, I'll get that after I pick it up with the forks and jack stands.
The water temp gauge started working after I shut the unit down with the emergency stop button and restarted it. Go figure. All gauges work and it runs good without load. I'm curious to see what the governor does under load. Searching for load bank next.
Put a fancy exhaust flapper on but it was too noisy, went back to the original cover flapper.
Got all the openings covered with hardware cloth except the large opening under the engine, I'll get that after I pick it up with the forks and jack stands.
Last edited:
robson1015
Active member
- 515
- 132
- 43
- Location
- New Concord, Ohio
Hardware cloth...
robson1015
Active member
- 515
- 132
- 43
- Location
- New Concord, Ohio
Hey Guyfang - I lowered those wires...Attachments
m32825
Active member
- 224
- 170
- 43
- Location
- Central Florida
I just did the quad fuse modification on mine, where do I get the scoop on the MOV mod?
-- Carl
m32825
Active member
- 224
- 170
- 43
- Location
- Central Florida
Aha, found it!
https://www.steelsoldiers.com/showthread.php?148791-MEP-802-and-803-Main-generator-tip
Post #29 has the details.
-- Carl
Bmxenbrett
Member
- 602
- 30
- 18
- Location
- NY
You can get name brand cheap filters from filterbarn.com. i ordered every filter for my 802 and i believe it was $36 shipped. I think that fuel filter was $7. Air was the expensive at $15.
- 3,816
- 5,894
- 113
- Location
- MA
You should use some of this same cloth material to cover up the drain holes in the underside of the machine (like under the battery trays).
robson1015
Active member
- 515
- 132
- 43
- Location
- New Concord, Ohio
Did that - just need to do the middle opening under the engine after I lift the unit up.
ISO group price for freq. cable = $180.00 - still looking
robson1015
Active member
- 515
- 132
- 43
- Location
- New Concord, Ohio
B.W. Elliott price= $250.00 -still looking
robson1015
Active member
- 515
- 132
- 43
- Location
- New Concord, Ohio
W.B Parts price = $275.00 - still looking
- 3,816
- 5,894
- 113
- Location
- MA
Oof... that Dorman cable looks better all the time, huh? Still waiting on my guy to get me a price.
robson1015
Active member
- 515
- 132
- 43
- Location
- New Concord, Ohio
One place quoted $450....wtf $100 would be more than enough for a $50 part. May go with the Dorman after all...