ramdough
Well-known member
- 1,554
- 1,729
- 113
- Location
- Austin, Texas
I have heard the same thing....6.5-7 was stock normal.
Sent from my iPhone using Tapatalk
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
FMTV High Speed Gears
- Thread starter NDT
- Start date
Sent from my iPhone using Tapatalk
- 5,637
- 381
- 83
- Location
- Spring Branch, TX
Last long drive I did I was keeping steady at about 55mph and got 6.3mpg. I'm willing to bet if I was going convoy speed at 45mph it would have been closer to 7.
- 1,006
- 1,905
- 113
- Location
- Wauchula, FL
I can't explain why mine was originally getting such terrible gas milage besides the obvious high RPM's at 55mph. But with over 2,000 miles on it prior to the gear change and checking it a few different ways, thats what I was getting. It surprised me to, but with no trouble codes or any other obvious cause I just have to accept it.
expeditionnw
Member
- 174
- 1
- 18
- Location
- Alaska
Keith also has an A1 with a C7 cat. Perhaps his economy is due to that. my 3116 sees a bit over 6mpg with factory gears.
sjohn116
New member
- 122
- 6
- 0
- Location
- Baltimore, Maryland
Can anyone advise about the speedo input and recalibration for a WTECII 3116 A0 truck?
scottmandu
Active member
- 822
- 36
- 28
- Location
- Texas
That's weird my 1084A1 with the C7 gets 5.8 mpg at approx 60 mph, and it's almost 9000 lbs heavier.
- 1,006
- 1,905
- 113
- Location
- Wauchula, FL
Please tell me the secret to better MPG. LOL!
scottmandu
Active member
- 822
- 36
- 28
- Location
- Texas
IDK I run the MRAP CTIS computer which I believe keep the tires at 100psi, versus the 75.
ramdough
Well-known member
- 1,554
- 1,729
- 113
- Location
- Austin, Texas
So what is a typical 1083+ MPG?
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
scottmandu
Active member
- 822
- 36
- 28
- Location
- Texas
I'd wager 5-6mpg..
ramdough
Well-known member
- 1,554
- 1,729
- 113
- Location
- Austin, Texas
So you lose 1 MPG for the added axle and weight? That does not sound too bad of a trade. Percentage wise it is huge, but by absolute numbers not so bad.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
scottmandu
Active member
- 822
- 36
- 28
- Location
- Texas
1951M1078
Well-known member
- 1,018
- 185
- 63
- Location
- Glendale,AZ
B416561 Is this the 3.07 set ?
scottmandu
Active member
- 822
- 36
- 28
- Location
- Texas
The hub reduction isn't 2:1 it's 1.71:1.
- 10,501
- 6,631
- 113
- Location
- Camp Wood/LC, TX
This statement is in direct contradiction of the info published in TM9-2320-365-10 section 1-13 equipment data.
scottmandu
Active member
- 822
- 36
- 28
- Location
- Texas
Whoever wrote the book didn't count the teeth.
scottmandu
Active member
- 822
- 36
- 28
- Location
- Texas
24/14 = 1.7143
Attachments
- 6,862
- 697
- 113
- Location
- Stratford/Connecticut
So would that make the fina drive ratio approx 6.70?
- 1,425
- 37
- 48
- Location
- Winter Haven, florida
Where do you get this info.? The chunk is marked 3.07 and the housing is marked 6.14 finial drive.