Staffsargent
Member
- 220
- 1
- 18
- Location
- Blakeslee, PA
Looking for the glass fuse for the fuel pump. P/N FO3B350V3A
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Fuse
- Thread starter Staffsargent
- Start date
- 7,058
- 148
- 63
- Location
- Mid Hudson Valley NY
Radio Shack has the 2 amp Slow Blow fuses
wsucougarx
Well-known member
- 6,951
- 67
- 48
- Location
- Washington State
Is this the small 1" glass cylinder type fuse w/metal caps at both ends? I'm putting a kit together for my first deuce pickup 
Boatcarpenter
New member
- 1,877
- 17
- 0
- Location
- Marlborough, NH
Yes it is.
BC
BC
wsucougarx
Well-known member
- 6,951
- 67
- 48
- Location
- Washington State
thank you
Staffsargent
Member
- 220
- 1
- 18
- Location
- Blakeslee, PA
Thank emmado22 for the answer. Went to Radio Shack. 4 fuses for $3.00
- 10,865
- 762
- 113
- Location
- Appomattox, VA
What was the Radio Shack part number for these fuzes?
Boatcarpenter
New member
- 1,877
- 17
- 0
- Location
- Marlborough, NH
- 10,865
- 762
- 113
- Location
- Appomattox, VA
My manual, 9-2320-361-20-1, says to use "4 amp" fuzes. What the difference between 2 amp and 4 amp? (if you answer 2 amps, I'm gonna break a beer bottle over your head next time I see you)
Attachments
FormerNewMVGuy
Active member
- 1,237
- 10
- 38
- Location
- stockton NJ
Well, I have put 3 amp slow blow fuse's in all 4 of my trucks, I seem to recall a thread about this a while back? I belive there was a PS article about stepping up from a 2 amp to a 3 amp fuse.
DanMartin
New member
- 1,276
- 16
- 0
- Location
- Hillsboro, Oregon (USA)
I had mine apart today to fix a leak in the fuse holder cover...it was completely full of fuel (bad tank gasket allowing fuel to slosh up into the cover through the wire bulkhead fitting I think). Anyways...it had a 2-1/2 amp fuse...guess the USAF just split the difference between the 2 and 3 amp changeover.
I need to replace my fuse because it is *full* of diesel fuel (yes...sloshing around in there...just think if it decided to get hot and blow!).
I'll be putting in another 2.5 amp if I can find it, but will go with 3 amp if I can't find them.
I need to replace my fuse because it is *full* of diesel fuel (yes...sloshing around in there...just think if it decided to get hot and blow!).
I'll be putting in another 2.5 amp if I can find it, but will go with 3 amp if I can't find them.
- 7,058
- 148
- 63
- Location
- Mid Hudson Valley NY
Anyone know how to calculate the amps the fuel pump draws?
2 amp, 2.5 amp, 3 amp, 4 amp... Who knows.. I do know that I bet A TON of trucks have BLOWN fuses in there......
2 amp, 2.5 amp, 3 amp, 4 amp... Who knows.. I do know that I bet A TON of trucks have BLOWN fuses in there......
jasonjc
Well-known member
- 5,326
- 290
- 83
- Location
- Gravette Ar.
A fuses should be 25% bigger than the amp draw.
DanMartin
New member
- 1,276
- 16
- 0
- Location
- Hillsboro, Oregon (USA)
Next time I get out to the truck I'll hook up the multimeter and see what it pulls. Probably close to 2A.
wsucougarx
Well-known member
- 6,951
- 67
- 48
- Location
- Washington State
Ah, 3 AMPs now. Need to go back to radio shack to get another set for the tool bag
bottleworks
New member
- 920
- 3
- 0
- Location
- Central NC
emmado22 said:
An electric motor is like a variable resistor. It's current draw will be based on the load of the motor. Measuring the winding's resistance and using Ohm's law would give incorrect real life results. Checking current draw with a multi meter in-line is the best way to go about it.
- 10,350
- 75
- 48
- Location
- Meadows of Dan, Virginia
Make sure it's the "Slow Blow" type, they can handle the higher inrush currents and spikes...wsucougarx said:
FreightTrain
Banned
- 2,730
- 13
- 0
- Location
- Gadsden,Al
Wrapper from a pack of smoke or Chewing gum works too....
bottleworks
New member
- 920
- 3
- 0
- Location
- Central NC
Does that have a fast blow or a slow blow rating? Part number available?FreightTrain said: