Geared Lug Wrench

[scrapdaddy]

I just got my lug wrench that were being sold on site, but mine didn't come with the handles. Anyone have the measurements of the handles, Length and Dia. maybe I can find some material that will work.

Thanks

 

[3dAngus]

Hummm.... I was just looking for a lug wrench. Do you know if yours will fit the M105 wheels? Is it the 2 piece? Its not on the classified anymore. What was the price and source?

 

[gimpyrobb]

Dell, you don't need a geared lug wrench for a 105. I have what you need, send me an addy.

 

[3dAngus]

I finally found my micrometers. They get legs sometimes. Lugs measure 1.5" on the M105.

Will PM you. Thanks.

 

[maddawg308]

The geared lug wrench only works with the rear duals on the deuce (and the 5-ton, etc). Won't work on the front wheels, or trailers that are single wheel. If you can't get the wheel off with a normal Budd wrench and a 3-foot bar, you need an impact wrench.

 

[Kohburn]

or try the reduction wrench from ebay - it's what I have and is amazingly easy to remove even severely stuck lugs nuts.

this is the one i have

NEW TORQUE MULTIPLIER LUG WRENCH TRUCK SEMI BUS TRACTOR | eBay

 

[maddawg308]

Kohburn, that tool looks pretty neat, but if it don't say "Made in the USA" you know where it is made. That means I don't buy it.

I don't want to start another China tools thread, please, just my two cents on the issue.

However, if I could find something like that made by people here at home, I'd spring for it in a heartbeat!

 

[thirdstreettito]

n00b question, what's a geared lug wrench?

 

[jimk]

The geared lug wrench only works with the rear duals on the deuce (and the 5-ton, etc). Won't work on the front wheels, or trailers that are single wheel

It will if you put a bar thru the large hole. Were they issued with 2 handles? I made a single double duty bar out of 3' long round stock (for large hole). I turned down one end a for a few inches so it does the small hole too.

 

[merlot566jka]

its a transmission... you are the engine, the lug nut is the tire.

 

[indy4x4fab]

page 30, left hand corner. i'm a dealer for ken-tool if u want pricing pm me.

http://www.kentool.com/catalogs/catalog_1-18-2010.pdf
TR44SW Set

also recommend 32610 support stand (page 29 lower left), makes life easer.

u pay freight u can have it for what ill pay for it, they aren't cheep tho.

 

[ryker725]

He said up front that they don't come with the handles.. I plan to order one today..

 

[m816Buch]

think i read somewhere that the tool originated in australia

 

[scrapdaddy]

Yeah, when I first seen the add, they were new in the box. I got one of the old ones. I was just looking for the size of the two bars, so I could make up some myself.

 

[Jake0147]

The small bar is 3/4 inch round bar, 21 inches in length.
The large bar is 1-1/8 inch DOM tube with a .175 inch wall, kind of beat up though, might be 3/16... Anyhow, it's 36 inches in length.
The large bar is the reaction member to steady the center gear in the absence of a bud cap.

 

[scrapdaddy]

Thanks Jake, That's what I was looking for. I read in the Ken-Tool cat. that the bars are heat treated. Maybe I better buy some rather than make them. The picture helped alot.

Ron

 

[firefox]

Thanks Jake, That helped me a bunch too. I have the geared wrench but never knew about using
the large handle as a reaction bar.
Bruce

 

[Jake0147]

I read in the Ken-Tool cat. that the bars are heat treated.

Ron

They might be heat treated... When I put ten new tires on my forty year old truck, I checked, and the bars are quite stout.

 

[houdel]

Same "TORQUE MULTIPLIER LUG WRENCH" from same supplier but cheaper off Ebay at his own website Welcome To LugWrench.Biz

 

[1stSarge]

I believe Kipman still has some very nice used ones. PM him. I got mine from him and I think it is the greatest thing to come along since sliced bread. What I used to do with a 5 foot bar I can now do with an 18” bar.