STRANGER /DANGER STRANGER /DANGER !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
How do you move your generator(s)?
- Thread starter Digger556
- Start date
I usually give them some wine, play some sad music and tell them about my childhood... they're moved to tears in minutes!
- 2,532
- 2,061
- 113
- Location
- Efland, NC
I’ve been on the lookout for a 420 or 430 loader for my old JD reactor.
I picked this 420 loader frame up in Pavo Ga at T & H Sales & Salvage. I fitted generic 2x18 cylinders to it and had all new hoses made. It increased the lift height by a bunch and should have given it the lift capacity of the 430 loader.
I love this idea! My garden tractor doesn’t have a 3 point but I can put a Jack on it. What’s you use for the axle? I tried to send you a message but I don’t think I have enough posts yetI don't own much in the way of material handling equipment and have typically relied on my tilt-deck trailer and a small dolly with floor jacks to move stuff around. Recently I built a pair of towable dollys to improve my ability to shuffle generators.
View attachment 905444
It got me curious how all of you move a half ton or more of surplus around.
1 inch cold rolled steel, turned down to 3/4" on the ends.
Jayhawk#44
Active member
- 89
- 148
- 33
- Location
- Arizona
MEP-803A, rented a forklift ($200) to get it off the trailer and in the garage. floor jacks to lift it, jack stands to hold it up.
Built a 4X4 frame between the rails and bolted 2 large fixed casters at the very center balance point. Then bolted 2 1/2 inch ish smaller swivel casters at the 4 corners. I can easily move it in, out, and around my garage with ease by myself. Jumps all gaps in the concrete with ease by just hitting 1 wheel at a time at an angle.
Got the idea off a post on here somewhere. Its buried right now, I'll post up some pics sometime when I unbury it.
Later,
Matt L.
Built a 4X4 frame between the rails and bolted 2 large fixed casters at the very center balance point. Then bolted 2 1/2 inch ish smaller swivel casters at the 4 corners. I can easily move it in, out, and around my garage with ease by myself. Jumps all gaps in the concrete with ease by just hitting 1 wheel at a time at an angle.
Got the idea off a post on here somewhere. Its buried right now, I'll post up some pics sometime when I unbury it.
Later,
Matt L.
Icesythe7
Active member
- 147
- 223
- 43
- Location
- Indiana, USA
- 6,078
- 4,458
- 113
I second the ringing endorsement of pallet forks on the tractor.
Attachments
- 3,157
- 1,703
- 113
- Location
- Pemberton, N.J.
Just be aware that bucket lip pallet forks WILL bend your bucket!! And once bent it will never grade properly again. The best bucket forks are like the ones I had on one of my backhoes that actually attached to hooks welded on top of the bucket in four spots across the top and that swung on those and the backs of the forks butted against the front of the cutting edge of the bucket. This way the weight was carried by the top of the bucket where the reinforced mounts for the cylinders are. No bent bottom bucket surface. You can modify old forklift forks to work this way if you have a good heavy duty welder.
- 6,078
- 4,458
- 113
They make forks with a frame that take the place of the bucket. They're not a lot more expensive than those bucket ruiners.
I have no idea how I ever lived without them.
- 3,157
- 1,703
- 113
- Location
- Pemberton, N.J.
They are great if you don't have a 65 year old tractor with frozen pins! You young'uns are to used to quick change implements.
My pallet fork is on a frame . No clamp on bucket forks here. And I love my quick disconnect attachments 5 minutes is all it take to switch attachments if they are side buy side .
I also recently drilled a hole in one of the forks so I can tread on a Reese hitch ball. That way if I’m trying to hang a rope or chain off the fork it can’t side off .
Sure bites rolling heavy drums full of diesel into the bucket and having to manually move them into place .
Sent from my iPhone using Tapatalk
- 1,030
- 1,484
- 113
- Location
- Wilson County, Texas
- 1,030
- 1,484
- 113
- Location
- Wilson County, Texas
- 7,732
- 19,808
- 113
- Location
- Charlotte NC
.
That's a neat all terrain lift truck!
Looks fairly old, but if it works - what they hay!
.
- 1,030
- 1,484
- 113
- Location
- Wilson County, Texas
1982. Fairly sure it was refurbished at some point. Got it recently & it needs some love, but it runs strong.
biscuitwhistler37
Well-known member
- 294
- 864
- 93
- Location
- Michigan
What model unit is that? I need something like it for the boatyard
- 1,030
- 1,484
- 113
- Location
- Wilson County, Texas
- 118
- 70
- 28
- Location
- Edinburg Texas
Backhoe/ skid steer OR when in a bind . Call a wrecker (flat bed ) guy charged me $75 To transfer it to the bed of truck . When offloading , I throw some pipe under and push it off the bed of the truck down a harbor freight ramp. slides fast as hell, but Never failed. For around the shop they sit on pipe to slide around as needed.I don't own much in the way of material handling equipment and have typically relied on my tilt-deck trailer and a small dolly with floor jacks to move stuff around. Recently I built a pair of towable dollys to improve my ability to shuffle generators.
View attachment 905444
It got me curious how all of you move a half ton or more of surplus around.
