-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
M101a2 wheel bearing seal
- Thread starter uglysteve
- Start date
AceHigh
Well-known member
- 2,175
- 30
- 48
- Location
- Princeton WV Lake City FL
Last edited:
![[thumbzup]](https://www.steelsoldiers.com/images/smilies/icon_smile_thumzup.gif "Thumbs Up [thumbzup]"){kind=icon}
blybrook
Member
- 310
- 1
- 18
- Location
- Fairbanks, AK
Napa has them for about $23 a piece. I just replaced mine when I replaced the parking brake cables.
EDIT - It is NAPA part number 22532 (found the receipt over lunch in the truck).
EDIT - It is NAPA part number 22532 (found the receipt over lunch in the truck).
Last edited:
gizip
New member
- 16
- 0
- 0
- Location
- Tappahannock, Va.
AceHigh is correct.........the 10-36 seals from etrailer.com are right. They cost $7.95 for TWO.
blybrook
Member
- 310
- 1
- 18
- Location
- Fairbanks, AK
I only went to napa so that I could get the trailer back up and going the same day. Plus most companies don't like to ship to AK, as they claim it's not continental US; so they give us international shipping. I have yet to deal with e-trailer, may have to give them a try in the future.
- 1,704
- 412
- 83
- Location
- Leavenworth, KS
blybrook,
Did you get a M101 recently from the DRMO here in Fairbanks? I am pending an EUC to pick mine up and was curious to know if yours needed new bearings or seals immediately? I know these were recently pulled from service here at FT Wainwright but most of them had not seen much use or maintenance in quite awhile.
I imagine it'd probably be wise to go ahead and plan on replacement, but if I can put it off I probably will. Too many other projects and all...
Did you get a M101 recently from the DRMO here in Fairbanks? I am pending an EUC to pick mine up and was curious to know if yours needed new bearings or seals immediately? I know these were recently pulled from service here at FT Wainwright but most of them had not seen much use or maintenance in quite awhile.
I imagine it'd probably be wise to go ahead and plan on replacement, but if I can put it off I probably will. Too many other projects and all...
blybrook
Member
- 310
- 1
- 18
- Location
- Fairbanks, AK
Sigo,
I'll PM you the information.
Bill
I'll PM you the information.
Bill
papakb
Well-known member
- 2,285
- 1,185
- 113
- Location
- San Jose, Ca
blybrook,
Where did you find the brake cables? Were they a Napa part also?
THX
Kurt
Where did you find the brake cables? Were they a Napa part also?
THX
Kurt
blybrook
Member
- 310
- 1
- 18
- Location
- Fairbanks, AK
Kurt,
No, I ordered them from Saturn Surplus per the part number that is listed in the TM. They turned out to be too long, so I had to modify how they mounted back to the frame at the handle side to prevent modifying the cable itself. I'll get a couple photos of that change in the near future. My modifications were essentially a new bolt mounted a few inches away from stock location and a spacer to hold the wire centered on the pulley back at the original mounting point.
Bill
Tymkpr
New member
- 15
- 0
- 0
- Location
- Norman, OK
I see the 10-36 is the bearing seal... OK
Now what would be the correct size hub bearing for the A2?
Picking up my A2 from Hooks later this month. Would like to have a couple in tool chest ready if I need to rebuild them before returning home 5 hours later.
Now what would be the correct size hub bearing for the A2?
Picking up my A2 from Hooks later this month. Would like to have a couple in tool chest ready if I need to rebuild them before returning home 5 hours later.
Tymkpr
New member
- 15
- 0
- 0
- Location
- Norman, OK
Dang it.... I just need to look deeper. I found the correct thread that help me on the bearing info sorry to have to ask the question again.
lindyp38
New member
- 788
- 0
- 0
- Location
- ulster county ny
just picked up my seals...will install asap......thanks
lindyp38
New member
- 788
- 0
- 0
- Location
- ulster county ny
they fit like a charm...thanks