M1101 Light Bulbs

[Cook4794]

Just won a GovPlanet auction. My trailer is a 2009 Schutt M1101. I've been trying to find if it has LED or incan\6descent bulbs that i'll have to switch over to 12 volt.


My question is...

I have a 24 to 12 volt conversion harness for my m101a3.

I'm guessing, If my trailer has 24V bubls it will not work with my conversion harness.

My contract ID is W56HZV-08-D-0107, But I'm not sure where I can find the specs regarding the trailer or if its even possible? I have searched on the forums and I believe i'll need a 1167 and a 63...I have the page saved in my bookmarks. I'll have to stop by a wal-mart on the way to pick up the trailer and get the correct bulbs if they are not all LED.


Is there a way I can look up my contract ID and find out if all my bulbs are LED and I'll be good to go?

 

[Gunzy]

Most of the M1101/1102 have LED marker lites which are 12/24 volt but the tail lamps are usually not LED so you will need to change those bulbs. 12 volts will run them but they will be very dim.

 

[Cook4794]

Most of the M1101/1102 have LED marker lites which are 12/24 volt but the tail lamps are usually not LED so you will need to change those bulbs. 12 volts will run them but they will be very dim.

AH, Roger that. I'll be driving during the day so it should be okay until I get to a wal-mart to get the right bulbs.

 

[Daybreak]

Just won a GovPlanet auction. My trailer is a 2009 Schutt M1101. I've been trying to find if it has LED or incan\6descent bulbs that i'll have to switch over to 12 volt.

Howdy,
I see its a 2009 model. It has LED lights.

It was after 2006 when they were changed to using the LED lights. My trailer was delivered 10/06 and has all incandescent.

This is my trailer;
All the bulbs are standard incandescent. So swap out the bulbs for the 12v counterparts for a brighter safer day.
PU-798A Unit = Mep-803a with a M1102 trailer
Rear brake, turn light bulbs #1683 24v bulbs swapped to #1156 12v bulbs
Marker lights all round #1251 24v bulbs swapped to #97 12v bulbs
Trailer plug =cut off mil end, cheap 7-way plug attached.

 

[porkysplace]

[h=1]12v bulbs for Composite Lights[/h]
[h=1]Bulbs, 12 volt, 24 volt, trailer, lights, info[/h]
[h=1]1990 M101a2 tail light bulbs 12V[/h]
[h=1]Bulb Voltage interchange Chart (6V 12V 24V, for trailers and trucks)[/h]

 

[Cook4794]

Update!My M1101 is a 2009, it has all led side markers but the tailights are incandescent. I switched them out with LED replacement bulbs and it

 

[texastrapper]

Marker LED Light on ebay
10X White 1156 BA15S 22-SMD LED Light bulb Tail Turn Signal Backup RV Camper 12V

Tail LED Lights on ebay
4x Piece Lot M1101/M1102 Military Trailer Tail Light 12v LED Replacement Bulbs

 

[NEIOWA]

Perhaps a better option would be LED rated for 12-24v so covers tow with civ or military vehicle as:
1157
https://www.amazon.com/LUYED-Extrem...F8&qid=1491791972&sr=8-2&keywords=1157+12-24v
and
1156
https://www.amazon.com/generation-1...F8&qid=1491792120&sr=8-1&keywords=1156+12-24v

 

[Sharky1528]

Wow.. I never thought about swapping the incandescent bulb's out to LED's... Sounds like I need to source some up for the M1102 !!

 

[Kevallarist]

I know this line is a bit old, but I am working on re-wiring my trailer now, I’ve done the military to 4 flat conversion.
My trailer is a 2009 Schutt m1101 but it doesn’t seem to have the bulbs like the others I’ve seen, the tail lights/blinkers are these one piece sets. Guessing in order to replace these with LED’s I’d have to get brand new housings?

 

[Godspeed131]

Deleted, responded before reading other thread